Valid

GB/T 39172-2020Non-steel wire rope suspension means for lifts (English PDF)

电梯用非钢丝绳悬挂装置

Preview PDF

This is a limited preview

Buy now to download the full PDF (35 pages)

Need quotation for your management?

Get a formal quotation for GB/T 39172-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

November 19, 2020

Implementation date

June 1, 2021

Scope

GB/T 39172-2020 is the English-translated version of 电梯用非钢丝绳悬挂装置.

GB/T 39172-2020 is the Chinese standard "Non-steel wire rope suspension means for lifts". Its scope clause reads: This standard specifies the classification, technical requirements, inspection, test, inspection rules and acceptance concerning non-steel wire rope suspension means for lifts.

This standard is applicable to non-steel wire rope suspension means involved in traction drive lifts, with steel wire ropes or non-metal materials as load-bearing members.

For non-steel wire rope suspension means of other new materials or structures, this standard may be used as a reference, and the inapplicable parts shall be determined by the supplier and the purchaser through negotiation.

Its clauses include terms and definitions; classification; technical requirements.

Found what you need?

Document preview — GB/T 39172-2020

National Standard of the People's Republic of China

ICS
91.140.90
Classification
Q 78

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword I
  • Introduction II
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Classification
  • 5 Technical requirements
  • 6 Inspection
  • 7 Tests
  • 8 Inspection rules
  • 9 Acceptance
  • 10 Marking and quality certificate
  • 12 Packaging, storage and transportation
  • Annex A (Informative) Specification of coated rope (belt)
  • Annex B (Normative) Technical conditions for scrapping and replacing coated ropes (belts)
  • Annex C (Normative) Determination of breaking force
  • Annex D (Normative) Determination of adhesive strength
  • Annex E (Informative) Bending fatigue test of coated rope (belt)
  • Annex F (Informative) Traction force and equivalent friction coefficient
  • Annex G (Informative) Marking and quality certificate
  • Annex H (Informative) Information required for the order
  • Annex I (Informative) Selection, operation and maintenance information
  • Annex J (Informative) Packaging and storage
  • Bibliography

1 Scope

This standard specifies the classification, technical requirements, inspection, test, inspection rules and acceptance concerning non-steel wire rope suspension means for lifts.

This standard is applicable to non-steel wire rope suspension means involved in traction drive lifts, with steel wire ropes or non-metal materials as load-bearing members. For non-steel wire rope suspension means of other new materials or structures, this standard may be used as a reference, and the inapplicable parts shall be determined by the supplier and the purchaser through negotiation.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB 7588-2003 Safety rules for the construction and installation of electric lifts

GB/T 12805-2011 Laboratory glassware - Burettes

GB/T 14684-2011 Sand for construction

GB/T 20285-2006 Toxic classification of fire effluents hazard for materials

GB/T 31821-2015 Specification for discard of the main parts of lifts

JB/T 10696.10-2011 Test methods for determining mechanical, physical and chemical properties of electric cables and wires - Part 10: Rat gnawing test

3 Terms and definitions

For the purposes of this document, the terms and definitions given in GB 7588 and the following apply.

3.1

non-steel wire rope suspension means suspension means for lifts except the steel wire rope suspension means, comprised of coated ropes, coated belts and termination devices thereof

3.2 load-bearing member

components in a coated rope or belt that bear breaking force

3.3 coated rope

rope-shaped combined construction in which one or more layers of non-metal materials wrap a single load-bearing member

3.4 coated belt

banded combined construction in which one or more layers of non-metal materials wrap multiple load-bearing members

3.5 coating

non-metal material wrapping the load-bearing member

3.6 minimum breaking force

a specified value which the breaking force measured using the specified method shall not be below

Note: In kN.

3.7 measured breaking force

breaking force measured using the specified method

Note: In kN.

3.8 residual breaking force

breaking force measured using the specified method after use and wear

Note: In kN.

4 Classification

4.1 Coated rope

4.1.1 Type

A coated rope shall be rope-shaped construction, which is expressed by R. See Annex A for the specifications of coated ropes.

4.1.2 Construction

A coated rope shall be composed of load-bearing member and coating. See Figure 1 for the schematic diagram for the cross section of a common coated rope.

Keys:

D——the nominal diameter of coated rope, mm;

d——the nominal diameter of load-bearing member, mm;

1——the coating;

2——the load-bearing member.

Figure 1 Schematic diagram for the cross section of a common coated rope

4.1.3 Designation

The designation of coated rope consists of the following contents:

Example:

A coated rope with a nominal diameter of 6.5mm, containing coating made of TPU, load-bearing member with a nominal diameter of 5.0mm and made of M, and with a minimum breaking force of 28.0kN, is designated as:

Coated rope - GB/T 39172-R-6.5/5.0-TPU/M-28.0

4.2 Coated belt

4.2.1 Types

A coated belt shall be a banded construction, which is expressed by B. Coated belt types are classified into flat type (BF) and tooth type (BT). See Annex A for the specifications of coated belts.

4.2.2 Construction
4.2.2.1

When the cross section of load-bearing member is circular, the coated belt shall be composed of load-bearing member and coating. See Figure 2 for the schematic diagram for the cross section of a common coated belt.

a) Flat type (BF) b) Tooth type (BT) (I) c) Tooth type (BT) (II)

Keys:

W——the nominal width of coated belt, mm;

T——the nominal thickness of coated belt, mm;

Tt1, Tt2——the distance from the center of load-bearing member to the contact surface between the coated belt and the traction sheave, or the distance from the center of load-bearing member to the tooth top of coated belt on the side in contact with the traction sheave, mm;

d——the nominal diameter of load-bearing member, mm;

t——the nominal thickness of load-bearing member, mm. For load-bearing member with a circular cross section, t=d;

1, 1a——the surface in contact with the traction sheave or the tooth top on the side in contact with the traction sheave;

2——the coating;

3——the load-bearing member.

Figure 2 Schematic diagram for the cross section of a coated belt with load-bearing member with a circular cross section 4.2.2.2 When the cross section of load-bearing member is noncircular, the coated belt shall be composed of load-bearing member and coating. See Figure 3 for the schematic diagram for the cross section of a common coated belt.

Keys:

W——the nominal width of coated belt, mm;

T——the nominal thickness of coated belt, mm;

Tt1, Tt2——the distance from the center of load-bearing member to the contact surface between the coated belt and the traction sheave, mm;

w——the nominal width of load-bearing member, mm;

t——the nominal thickness of load-bearing member, mm;

1, 1a——the surface in contact with the traction sheave;

2——the coating;

3——the load-bearing member.

Figure 3 The schematic diagram for the cross section of a coated belt with load-bearing member with a noncircular cross section

4.2.3 Designation

The designation of coated belt consists of the following contents:

Example 1:

A coated rope with a nominal width of 30mm and a nominal thickness of 3.3mm, containing 10 load-bearing members with a nominal diameter of 2mm and made of M, and coating made of TPU, and with a minimum breaking force of 43kN, is designated as:

Coated belt - GB/T 39172-BF-30×3.3/10×2-TPU/M-43

Example 2:

A coated belt with a nominal width of 25mm and a nominal thickness of 4.5mm, containing 4 load-bearing members with a nominal width of 5mm and a nominal thickness of 2.5mm and made of N, coating made of TPU, and with a minimum breaking force of 110kN, is designated as:

Coated belt - GB/T 39172-BF-25×4.5/4×5×2.5-TPU/N-110

5 Technical requirements

5.1 Load-bearing member

5.1.1 Tensile strength

The nominal tensile strength shall be in the range of 1,570N/mm2 to 3,500N/mm2.

The nominal tensile strength shall be the lower limit of tensile strength of load-bearing member, and the deviation of tensile strength shall not exceed 390N/mm2.

Note: When the load-bearing member is made of metal material such as steel wire, the tensile strength refers to the tensile strength of the steel wire. When the load-bearing member is made of non-metal material, the tensile strength refers to the tensile strength of a single load-bearing member. For example, the nominal tensile strength of load-bearing member is 2,400N/mm2, while its upper limit of tensile strength is 2,790N/mm2.

5.1.2 Surface treatment

For metal load-bearing members, the metal wire shall be subjected to anti-corrosion treatment.

5.1.3 Joints

For metal load-bearing members, the metal wire shall have no joints.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 35 pages — is available in the English PDF.

Similar standards

How to Download GB/T 39172-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
35 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 39172-2020

$530.00