GB/T 38964-2020Isothermal forging for titanium-alloy - Technological specification (English PDF)
钛合金等温锻造 工艺规范
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38964-2020 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 21, 2020
Implementation date
February 1, 2021
Scope
GB/T 38964-2020 is the English-translated version of 钛合金等温锻造 工艺规范.
GB/T 38964-2020 is the Chinese standard "Isothermal forging for titanium-alloy - Technological specification". Its scope clause reads: This standard specifies the process specifications for titanium alloy isothermal forgings (hereinafter referred to as "forgings"), including general rules, requirements, and process.
This standard applies to the formulation of titanium alloy isothermal forging process. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 38964-2020
National Standard of the People's Republic of China
- ICS
- 77.120.50
- Classification
- J 32
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 General
- 5 Requirements
- 6 Process
1 Scope
This standard specifies the process specifications for titanium alloy isothermal forgings (hereinafter referred to as "forgings"), including general rules, requirements, and process.
This standard applies to the formulation of titanium alloy isothermal forging process.
2 Normative references
The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this article
Pieces. For undated references, the latest version (including all amendments) applies to this document.
GB/T 2965 Titanium and titanium alloy bars
GB/T 8541 Forging terminology
GB/T 9452-2012 Method for measuring effective heating area of heat treatment furnace
GB/T 16598 Titanium and titanium alloy cakes and rings
GB/T 23605 Titanium alloy beta transformation temperature measurement method
3 Terms and definitions
The following terms and definitions defined in GB/T 8541 apply to this document.
3.1 Titanium alloy alpha beta forging alpha beta
Titanium alloys are forged after heating at 20°C~50°C below the beta transformation temperature (Tbeta), that is, conventional two-phase zone forging to obtain a dual-state structure or
Isometric organization.
3.2 Titanium alloy near beta forging near beta forging of
Titanium alloys are forged after heating at 10°C~20°C below the beta transition temperature (Tbeta), and the primary alpha phase content is usually 15%~
30% dual-state organization.
3.3 Titanium alloy quasi beta forging of
The titanium alloy is preheated at 10°C below the beta transformation temperature (Tbeta) and then heated with the furnace to 30°C above the beta transformation temperature (Tbeta), and then heated for a short time.
Forging is performed to obtain a net basket organization or two-state organization with a primary alpha-phase content of not more than 15%.
3.4 Titanium alloy beta forging beta
Titanium alloys are forged after heating in the beta zone at 10°C or higher above the beta transformation temperature (Tbeta), and the primary alpha phase content is usually obtained
Not more than 15% net basket organization or sheet organization.
3.5 Isothermal forging of titanium-aloy
During the titanium alloy die forging process, the blank temperature is kept constant forging method. Under normal circumstances, the mold temperature is the temperature of the forged workpiece
95%~100% of the pressure, the pressure holding time is usually 60s~900s.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 38964-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 38964-2020
$150.00