Valid

GB/T 38618-2020Information technology - Telecommunications and information exchange between systems - Specification for high reliability and low latency wireless network communication protocol (English PDF)

信息技术 系统间远程通信和信息交换高可靠低时延的无线网络通信协议规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (27 pages)

Need quotation for your management?

Get a formal quotation for GB/T 38618-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

April 28, 2020

Implementation date

November 1, 2020

Scope

GB/T 38618-2020 is the English-translated version of 信息技术 系统间远程通信和信息交换高可靠低时延的无线网络通信协议规范.

GB/T 38618-2020 is the Chinese standard "Information technology - Telecommunications and information exchange between systems - Specification for high reliability and low latency wireless network communication protocol".

Its scope clause reads: This standard specifies the operating frequency range, radio frequency requirements and services of the physical layer of wireless communication networks in high-reliability and low-latency application scenarios, and data link layer reference architecture, MAC layer functions, precise time synchronization, data link sublayer functions, and adaptive channel hopping and determinism Scheduling etc. This standard applies to the planning, deployment and implementation of wireless networks in industrial-level field applications. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 38618-2020

National Standard of the People's Republic of China

ICS
35.110
Classification
L 79

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Abbreviations
  • 5 Overview
  • 6 Physical layer
  • 6.1 Overview
  • 6.2 Operating frequency range
  • 6.3 Physical layer RF requirements
  • 6.4 Physical layer service specification
  • 7 Data link layer
  • 7.1 Data link layer reference model
  • 7.2 MAC layer
  • 7.3 Data link sublayer

1 Scope

This standard specifies the operating frequency range, radio frequency requirements and services of the physical layer of wireless communication networks in high-reliability and low-latency application scenarios.

And data link layer reference architecture, MAC layer functions, precise time synchronization, data link sublayer functions, and adaptive channel hopping and determinism

Scheduling etc.

This standard applies to the planning, deployment and implementation of wireless networks in industrial-level field applications.

2 Normative references

The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this article

Pieces. For undated references, the latest version (including all amendments) applies to this document.

GB 15629.11-2003 Information technology system telecommunications and information exchange between local area network and metropolitan area network specific requirements

Part 11.Wireless LAN media access control and physical layer specification

GB/T 15629.15-2010 Information technology system telecommunications and information exchange specific requirements for local area networks and metropolitan area networks

Part 15.Low-speed wireless personal area network (WPAN) media access control and physical layer specification

GB/T 26790.1-2011 Industrial Wireless Network WIA Specification Part 1.WIA System Structure and Communication Specification for Process Automation

IEEE802.15.4-2011 Local Area Network and Metropolitan Area Network Part 15.4.Low Rate Wireless Personal Area Network

3 Terms and definitions

The following terms and definitions defined in GB/T 26790.1-2011 apply to this document. For ease of use, the following is repeated

Some terms and definitions in GB/T 26790.1-2011.

3.1 Adaptive frequency hopping

In each time slot of the communication phase in the industrial wireless network superframe cluster, the communication channel is changed according to the actual channel conditions.

[GB/T 26790.1-2011, definition 3.1.3]

3.2 Adaptive frequency switching

In the industrial wireless network superframe, the beacon phase and the active period replace the communication channel according to the actual channel condition within a superframe period.

Different channels are used in different super frame periods.

[GB/T 26790.1-2011, definition 3.1.4]

3.3 Beacon

In industrial wireless networks, the access point or the terminal node device that acts as the parent node broadcasts the frame of the node.

Note. The beacon frame is used for a new parent node or terminal node to join the industrial wireless network.

3.4 broadcast

Send the packet to all the nodes that can be received in the industrial wireless network.

[GB/T 26790.1-2011, definition 3.1.8]

3.5 channel

The radio frequency medium used to transfer packets from the sender to the receiver.

3.6

A logical node group including a parent node and multiple terminal nodes.

3.7 coexist

A network has the ability to perform tasks without being disturbed or disturbing other networks in the same environment.

Note. These networks follow the same or different rules.

3.8 compatible

A network can provide services to or receive services from other networks, and realize multiple networks through service exchange

The ability to operate effectively between.

3.9 Data link sublayer

Located above the MAC layer, it is used to process industrial wireless network topology, link and communication resources.

[GB/T 26790.1-2011, definition 3.1.17]

3.10 Terminal node

Equipment installed in the industrial site to connect or control the production process.

3.11 Frequency hopping

Transceiving channel switching method, the purpose is to resist interference and reduce signal fading.

[GB/T 26790.1-2011, definition 3.1.20]

3.12 Access Point

Devices that connect industrial wireless networks with other factory networks.

3.13 Hop

In industrial wireless networks, the process of packet transmission between two adjacent nodes without the participation of other nodes.

Note. Multi-hop is used to extend the transmission distance, bypass interference sources and avoid blocking.

3.14 Interoperability

The ability of two or more networks to exchange information with each other and to utilize the exchanged information.

3.15 Join

Industrial wireless network nodes are authenticated and allowed to access the industrial wireless network.

6.3.1.5 Receiver ED

The test scenario of the receiving end ED of the 433MHz~510MHz frequency band module should conform to the stronger one based on GB 15629.11-2003

Interference scenario, that is, there are at least two commercial wireless networks, and they are continuously connected with two commercial wireless networks for data exchange.

In this scenario, the ED curve of each channel in the 433MHz frequency band meets the accuracy requirements of 6dB2), and it is linear in this range.

And moderately monotonous.

6.3.2 RF requirements for 470MHz~510MHz frequency band
6.3.2.1 Modulation method

The receiving end of the 470MHz~510MHz frequency band module uses GFSK modulation, and the data rate is 100kbit/s.

6.3.2.2 Receiver sensitivity

The sensitivity of the module receiver in the 470MHz~510MHz frequency band should meet. in each channel of the 470MHz~510MHz frequency band,

When the receiver sensitivity drops to -107dBm1), the packet error rate is not more than 1%.

6.3.2.3 Interference suppression at the receiving end (adjacent channel)

The interference suppression (adjacent channel) at the receiving end of the 470MHz~510 MHz frequency band module should meet. when the interference signal power rises to

-50dBm1), the packet error rate is not more than 1%.

The specific condition is that the input power in the working channel is equal to -82dBm1), and the input power of the interference signal of the interval channel to the working channel is equal to

The value is at least 0dB2).

6.3.2.4 Interference suppression at the receiving end (non-adjacent channels)

470MHz~510MHz frequency band module receiving end interference suppression (non-adjacent channel) should meet. when the interference signal power rises to

-35dBm1), the packet error rate is not more than 1%.

The specific condition is that the input power in the working channel is equal to 82dBm1), and the input power of the interference signal of the non-adjacent channel to the working channel is the same.

The value is at least 30dB2).

6.3.2.5 Receiver ED

The test scenario of the receiving end ED of the 470MHz~510MHz module should meet the strong interference based on GB 15629.11-2003

The scenario is that there are at least two commercial wireless networks, and they are continuously connected to two commercial wireless networks for data exchange. here

In the scene, the ED curve of each channel in the 470MHz~510MHz frequency band meets the accuracy requirements of 6dB2), within this range.

It is linear and moderately monotonous.

6.3.3.1 Modulation method

The receiving end of the 780MHz frequency band module uses O-QPSK modulation, and the data rate is 250kbit/s.

6.3.3.2 Receiver sensitivity

The receiver sensitivity of the 780MHz frequency band module should comply with. In each channel of the 780MHz frequency band, the receiver sensitivity is reduced

-100dBm1), the packet error rate is not more than 1%.

6.3.3.3 Interference suppression at the receiving end (adjacent channel)

The interference suppression (adjacent channel) at the receiving end of the 780MHz frequency band module should meet. when the interference signal power rises to -40dBm1), the packet error

The rate is not more than 1%.

The specific condition is that the input power in the working channel is equal to -82dBm1), and the input power of the interference signal of the interval channel to the working channel is equal to

The value is at least 0dB2).

6.3.3.4 Interference suppression at the receiving end (non-adjacent channels)

The interference suppression (non-adjacent channel) at the receiving end of the 780MHz frequency band module should meet. when the interference signal power rises to -25dBm1), the error

The package rate is not more than 1%.

The specific condition is that the input power in the working channel is equal to -82dBm1), the input power of the interference signal of the non-adjacent channel to the working channel

The relative value is at least 30dB2).

6.3.3.5 Receiver ED

The test scenario of the receiving end ED of the 780MHz frequency band module should meet the strong interference scenario based on GB 15629.11-2003.

That is, there are at least two commercial wireless networks, and they are continuously connected to two commercial wireless networks for data exchange. In this scenario

The ED curve of each channel of the 780MHz module satisfies the accuracy requirement of 6dB2), which is linear and moderately monotonous in this range.

6.3.4 Coexistence of Same Frequency Commercial Wireless Network
6.3.4.1 Definition of Coexistence

The coexistence of co-frequency commercial wireless networks is defined as high-reliability and low-latency wireless networks that work in the 2.4GISM frequency band.

The frequency band is based on the channel interference of the GB 15629.11-2003 wireless network to achieve coexistence with the GB 15629.11-2003 wireless network.

The coexistence test is mainly carried out under three different levels of wireless network interference scenarios based on GB 15629.11-2003.

6.3.4.2 Interference scenario

3 wireless network interference scenarios based on GB 15629.11-2003.

a) Interference scenario 1--light interference scenario. In this interference scenario, there is a commercial GB 15629.11-2003 wireless network, and

The commercial wireless network has not made a deliberate network connection, that is, has not constructed deliberate data interaction interference;

b) Interference Scenario 2-General Interference Scenario. In this interference scenario, there are at least 2 commercial GB 15629.11-2003 wireless networks

Network, and make a deliberate intermittent network connection with one of the commercial GB 15629.11-2003 wireless networks, that is, a small amount of

Data interaction without continuous interference;

c) Interference scenario 3-Strong interference scenario. In this interference scenario, there are at least 2 commercial GB 15629.11-2003 wireless networks

Network, and with two commercial GB 15629.11-2003 wireless networks for purposeful continuous network connection, that is, continuous data interaction.

6.3.4.3 Co-existence determination of co-frequency commercial wireless networks

The coexistence of the 2.4GHz module and the same-frequency commercial wireless network shall comply with the wireless network interference scenario 1 in GB 15629.11-2003 respectively.

In the line network interference scenario 2, the wireless network interference scenario 3, the 2.4GHz module can automatically jump to the 2.4GHz frequency band and is not affected by the current wireless network.

It can communicate with the channel interfered by the working channel of the network to realize coexistence with the GB 15629.11-2003 wireless network.

6.4 Physical layer service specification

6.4.1 Physical layer reference model

The reference model of the physical layer (PHY) service is shown in Figure 2.

The physical layer defines two services. PHY data service connected to the physical layer data service access point (PDSAP) and connected to the physical layer

Layer management entity service access point (PLMESAP) PHY management service. The physical layer management entity (PLME) maintains a

Identify the MAC command being used. The payload field of the command frame contains the MAC command itself. The payload field of the command frame has a variable length, and

And it contains specific and different data from the command frame type.

7.2.2 Accurate time synchronization
7.2.2.1 Classification

The key technology of time synchronization is mainly divided into the advertising frame/beacon frame time synchronization method and the command frame time synchronization method.

7.2.2.2 Beacon frame time synchronization

The beacon frame time synchronization is one-way time synchronization based on broadcasting. In order to reduce the energy overhead caused by time synchronization, the IEEE In the 802.15.4-2011 physical layer industrial wireless network, beacon frames can be used to complete time synchronization. Beacon frame time synchronization steps as follows.

a) The access point periodically broadcasts time synchronization beacon frames to its neighbor parent nodes, and loads the beacon transmission time into the beacon frame

Designated fields;

b) The parent node generates an SFD interrupt when receiving a beacon frame and records the local beacon reception time;

c) The parent node calculates the time deviation between the clock of the node and the standard clock through the timestamps obtained by sending and receiving, and compensates for the local clock,

In this way, synchronization with the time source node is realized.

Similarly, in the star network, the parent node periodically broadcasts beacon frames, and the terminal nodes in the star network also receive beacon frames to complete synchronization.

In this way, all nodes in the network can synchronize with their own time sources, and finally complete the time synchronization of the entire network.

7.2.2.3 Command frame time synchronization

In order to meet the accuracy requirements of different industrial applications, the accuracy of time synchronization can reach milliseconds (ms) or even tens of microseconds (µs).

Reliable low-latency wireless networks can also use dedicated time synchronization command frames for secondary synchronization.

The time synchronization command frame can be sent periodically by the access point and the terminal node acting as the parent node.

--- The access point uses the inter-cluster communication period to send time synchronization command frames to achieve time synchronization of the mesh network;

--- The parent node uses the intra-cluster communication period to send time synchronization command frames to achieve time synchronization in the star network.

In the specific design of the time synchronization command frame, the following two command frame synchronization methods should be adopted.

a) Periodic broadcast synchronization. The time source node periodically sends time synchronization command frames, which is similar to beacon frame synchronization.

b) Point-to-point synchronization on demand. The node applies for the time synchronization command frame from the time source. The steps are as follows.

1) The node sends a synchronization request to load and send the time stamp T1 to the time source node;

2) The time source node receives the request, records the received request time T2, and parses the time information in the request;

3) The time source node sends a time synchronization command frame to the node at T3, and the synchronization node needs to receive the command frame at T4;

The node that needs to be synchronized calculates the time deviation theta value and the synchronization frame transmission time d by equations (1) and (2).

theta= (T1-T2)-(T4-T3) (1) d= (T2-T1) (T4-T3) (2)

In formula (1) and formula (2).

theta --- time deviation;

d ---Synchronous frame transmission time;

T1 --- node sending time;

T2 --- the time when the source node receives the request;

T3 ---Synchronization command frame sending time;

T4 ---Command frame receiving time.

4) The application synchronization node compensates its local clock according to the calculated time deviation.

7.2.2.4 Multi-hop network time synchronization compensation
7.2.2.4.1 Synchronous compensation

In large-scale thousands-point wireless network applications with high reliability and low latency, data messages sent by terminal nodes often need to be transmitted through multiple hops

Only the input can reach the access point, and the time synchronization accuracy error will accumulate as the number of hops increases. Multi-hop network time synchronization should be synchronized

Step compensation.

7.2.2.4.2 Fitting frequency drift

In addition to the initial time deviation of the two device clocks, the source of time synchronization error is the crystal drift of the clock is the most important factor.

The algorithm that uses multiple synchronizations to do linear fitting to the clock's crystal frequency drift can compensate for the drift value. When the algorithm has established a function

The clock synchronization model is shown in equation (3).

Tn=alphaTm beta (3)

Where.

Tn --- Receiving time of synchronization frame;

alpha --- Crystal frequency drift;

Tm --- send time;

beta --- Original time deviation.

Periodic synchronization can get multiple time data points, and the parameter fitting of these points can get the frequency drift and time deviation value.

7.2.2.4.3 Statistical parameter estimation

Another important source of time synchronization error is the time delay in the sending, transmission and reception of synchronization messages, including

Deterministic delay and uncertainty delay. In order to reduce the time delay error, the statistical signal processing method is used to estimate the time deviation.

The clock synchronization model is shown in equation (4).

TSA2i =fskew×(TS1i XSAi dSA) thetaSAoffset (4)

Where.

TSA2i ---The synchronization message reception time of node A for the i-th synchronization;

TS1i --- Time source node S synchronization message sending time;

fskew---the relative frequency drift of the two nodes;

thetaSAoffset---the original time deviation of the two nodes;

dSA --- message transmission time (deterministic delay);

XSAi --- Random delay during message transmission (uncertainty delay).

Assuming that XSAi obeys the Gaussian normal distribution, the maximum likelihood estimation can be used to estimate the time deviation to obtain the time deviation.

Shift value.

7.2.2.4.4 Monitor synchronization

Monitor synchronization is used to reduce the accumulation of multi-hop network synchronization errors. This method uses the "monitoring" effect produced by the broadcasting characteristics of the wireless channel

As a result, the node at the next hop can monitor the synchronization process between the node of the current layer and the node of the previous hop within the broadcast range to achieve the goal of synchronization.

of. In this way, it can effectively control and reduce the number of hops in the transmission of synchronization messages and reduce the accumulation of errors.

7.3 Data link sublayer

7.3.1 Data link sublayer functions
7.3.1.1 Function overview

The DLSL for high-reliability and low-latency wireless networks provides service interfaces for the network layer and the MAC layer. DLSL includes the number of data link sublayers

Data Entity (DLDE) and Data Link Sublayer Management Entity (DLME). DLDE is responsible for providing data service interface, DLME is used for configuration

DLSL parameters and monitoring the operation of DLSL.

7.3.1.2 Coexistence

High-reliability and low-latency wireless networks need to consider the coexistence of other industrial-grade wireless networks, and ensure that the network will not be

Operational interference problems due to other external factors. After the coexistence problem is solved, the interconnection problem of the network can be considered. That is different from

Wireless network connection improves the interoperability of industrial applications.

7.3.1.3 Time slot communication

The key to time slot communication is that the transmission of the frame must be completed within a limited time, that is, the frame must be transmitted in the specified time slot and cannot be delayed.

late. The time slot length of the data link sublayer in the high-reliability and low-latency wireless network is maintained with the time slot length of the IEEE802.15.4-2011 protocol compatible.

The high-reliability and low-latency wireless network supports variable-length time slots. The length of the time slot is set by the network manager after the node joins the network.

7.3.1.4 Superframe

High-reliability and low-latency wireless networks can selectively use superframe structures, and there can be multiple superframes, and each superframe is in the adjacent working range

There are different channel hopping sequences inside, and there are multiple time slots, each of which can be configured as a corresponding link. Super frame format by network

Manager definition. Super frames can be divided into two types. management super frames and data super frames.

a) The management superframe is generally used to complete the management of nodes;

b) Data superframes are generally used to configure communications related to user application processes.

The super frame is defined by the network beacon and sent by the terminal node acting as the parent node. The first time slot is the PAN beacon frame. Beacon frame

Transmission is performed in the first time slot of each superframe. If the master node does not use the superframe structure, then it will turn off the beacon transmission. letter

The mark is mainly used to synchronize each slave node with the master coordinator, identify the PAN, and describe the structure of the superframe. If any slave node wants to be in two

To communicate during the contention access period (CAP) between beacons, it is necessary to use multiple access with time slot and conflicting carrier detection (CSMA/

The CA) mechanism competes and communicates with other nodes, and only the node that has obtained the channel access permission in the current time slot can transmit in the time slot.

Send or receive frames. All transactions that need to be processed will be processed before the next network beacon slot. During the competition-free period (CFP), data

The transmission does not use the CSMA/CA mechanism. As long as the device is allocated a GTS, the device can directly perform data in the GTS containing time slot

Transmission.

In order to reduce the power consumption of nodes, the superframe is divided into two parts, namely the active part and the static part. In the static part, the master coordinator and

PAN nodes do not have any contact, enter a low-power mode, in order to achieve the purpose of reducing node power consumption.

7.3.1.5 Link

The link contains time and frequency, and determines how the node will occupy the time slot for data transmission. The type of link includes sending link, receiving link

And share the transmission link. Among them, in the shared transmission link, nodes can simultaneously compete to use the link to send data. And in the sending link and receiving

The receiving link can only allow the designated node to use the link to send and receive data.

7.3.2 Adaptive channel hopping
7.3.2.1 Overview of adaptive channel hopping function

In high-reliability and low-delay wireless networks, network nodes should support adaptive channel hopping.

Adaptive channel hopping technology is a major anti-interference technology in short-range wireless communication networks. High reliability and low latency wireless network channel

The sequence can be pre-designated by the network manager, and 3 channel hopping methods can be used. User-specified parameters such as channel hopping sequence and interval time

After that, the hardware can directly complete the frequency management, and jump to the designated channel w...

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 27 pages — is available in the English PDF.

Similar standards

How to Download GB/T 38618-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
27 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 38618-2020

$480.00