GB/T 36613-2018Probe test method for light emitting diode chips (English PDF)
发光二极管芯片点测方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 36613-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 17, 2018
Implementation date
January 1, 2019
Scope
GB/T 36613-2018 is the English-translated version of 发光二极管芯片点测方法.
GB/T 36613-2018 sets out how light emitting diode chips are measured by probe testing, the automatic method in which the chips are contacted by probes and read by a program-controlled instrument.
It specifies the test conditions and steps and the probe test methods for the optical parameters, the direct current electrical parameters and the electrostatic discharge sensitivity of the chips.
It defines terms such as probe test, parameter map, transient test, photoreceiver, chuck and ink pin. It applies to visible light package chips and thin film chips in mass production, and may be used as a reference for ultraviolet and infrared chips and for epitaxial wafers; thermal parameters and AC characteristics are not covered. It was issued on 17 September 2018 and has applied since 1 January 2019.
Found what you need?
Document preview — GB/T 36613-2018
National Standard of the People's Republic of China
- ICS
- 31.260
- Classification
- L 45
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 chip test conditions and steps
- 5 electrical parameters point test
- 6 Optical parameter point measurement
- 7 Electrostatic discharge sensitivity point test
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
Introduction
The semiconductor light-emitting diode chip is the core component of the light-emitting diode device, and its performance directly affects the light-emitting diode device.
Applications in semiconductor lighting products. How to accurately test the photoelectric performance of a semiconductor light-emitting diode chip, and become a chip manufacturing and use An important part. The standard was developed to ensure reliable and stable chip quality while scaled up.
1 Scope
This standard specifies the light-emitting diode chip (hereinafter referred to as "chip") optical parameters, direct current parameters and electrostatic discharge sensitivity point measurement Conditions and point test methods.
This standard is applicable to the detection method of the visible light emitting diode package chip and thin film chip for mass production. Ultraviolet light, infrared light The photodiode chip and the spot measurement of the epitaxial wafer can also be referred to.
This standard does not apply to the thermal parameters and AC characteristics of LED chips.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.
SJ/T 11394-2009 Semiconductor Light Emitting Diode Test Method
SJ/T 11395-2009 Semiconductor lighting terminology
SJ/T 11399-2009 Semiconductor light-emitting diode chip test method
3 Terms and definitions
The following terms and definitions defined by SJ/T 11395-2009 apply to this document.
3.1 Spot test
A method for automatically detecting the photoelectric performance and parameters of a chip.
Note: Using an automatic program-controlled test instrument in the form of probe contact, the chip is arranged according to a certain rule for transient test, and can be shaped according to the position of each chip. Into the parameter distribution map.
3.2 Parameter map
After the chip is tested, a color map indicating the photoelectric parameter test value by color is formed according to the position of the chip.
3.3 Transient test
The millisecond-level pulse is used to drive the lighting chip. During the test time, the process control test instrument automatically reads a plurality of photoelectric parameter values.
3.4 Receiver
An instrument used to collect the luminous intensity or radiant power of a chip under test.
3.5 Slide chuck
The chassis used to carry the chip in the spot test and provide electrical contact with the back electrode of the chip.
3.6 Ink needle
A device for applying ink to a chip that does not meet the parameter requirements.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 36613-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
SJ/T 11394-2009 — Measure methods of semiconductor light emitting diodes
SJ/T 11395-2009 — Semiconductor lighting terminology
SJ/T 11399-2009 — Measurement methods for chips of light emitting diodes
GB/T 36613-2018
$145.00