Valid

GB/T 36048-2018Passenger cars physical layer technical specification of CAN bus (English PDF)

乘用车CAN总线物理层技术要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (27 pages)

Need quotation for your management?

Get a formal quotation for GB/T 36048-2018 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

March 15, 2018

Implementation date

October 1, 2018

Scope

GB/T 36048-2018 is the English-translated version of 乘用车CAN总线物理层技术要求.

GB/T 36048-2018 specifies the physical layer of the high-speed CAN bus used in passenger cars, for communication rates from 125 kbit/s to 1 Mbit/s. It defines the terms used, such as bus state, internal capacitance and resistance of a node, propagation time and wake-up filter time, and sets the general requirements of the physical layer.

It then covers physical layer signalling, with bit encoding and decoding, bit timing, hard synchronization and resynchronization, and the electrical requirements of the high-speed media access unit, including versions with a low power mode and with a selective wake-up function, bus leakage current and connectors.

A final clause deals with bus failure management. Vehicle manufacturers, ECU suppliers and transceiver makers use it. It was issued on 15 March 2018 and has applied since 1 October 2018.

Found what you need?

Document preview — GB/T 36048-2018

National Standard of the People's Republic of China

ICS
43.040.40
Classification
T 24

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • 1 Scope4
  • 2 Terms and Definitions4
  • 3 General Requirements of Physical Layer7
  • 4 Physical Layer Signaling8
  • 5 High-Speed Media Access Unit14
  • 6 High-Speed Media Access Unit with Low Power Mode21
  • 7 High-Speed Media Access Unit with Selective Wake-up Function25
  • 8 Bus Failure Management27

1 Scope

This Standard specifies the terms and definitions of the physical layer of the high-speed CAN bus, the general requirements of the physical layer, technical requirements of physical layer signaling, high-speed media access unit, and bus failure management.

This Standard is applicable to high-speed CAN buses with communication rate from 125Kbit/s to 1Mbit/s.

2 Terms and Definitions

The following terms and definitions are applicable to this document.

2.1 Controller area network; CAN

A network communication technology for road vehicles.

2.2 Bus

A network communication topology that all nodes access to the network through a two-way transmission mode.

2.3 Bus state

One of two opposite logical states. explicit or implicit.

2.4 Physical layer

The electrical circuit (bus comparator and bus driver) that connects the CAN nodes to the bus; it consists of three parts, namely, analog circuit, digital circuit and analog signal on the CAN bus, and digital signal interface circuit inside the CAN node.

NOTE: The maximum number of nodes allowed to connect on the CAN bus depends on the electrical load of the CAN bus.

2.5 Physical media (of the bus)

A pair of shielded or unshielded twisted pair cables for signal transmission.

2.16 Internal capacitance (of a CAN node), Cin

The capacitance measured under CAN_L (or CAN_H) in the implicit state, when the CAN node is disconnected from the bus.

2.17 Internal delay time (of a CAN node), Tnode

The sum of all asynchronous delays that occur during the transmission or reception; it is related to the bit time logic unit of each node integrated circuit.

2.18 Internal resistance (of a CAN node), Rin

The resistance measured under CAN_L (or CAN_H) in the implicit state, when the CAN node is disconnected from the bus.

2.19 Supply voltage, Vcc

The voltage supplied to the bus transmitter, receiver, and optional split termination in the normal operating mode.

2.20 Split termination voltage, VSplit

The output voltage of split termination of CAN node relative to the signal ground of the module.

2.21 Propagation time, tProp

The time from a transmission data input edge of the medial access unit to a corresponding reception data output edge.

2.22 Wake-up frame

A CAN data frame used to wake-up one or more CAN nodes.

2.23 Wake-up filter time, twake

The explicit signal duration that can force the CAN node to wake up on the buses of CAN_H and CAN_L.

2.24 Activity filter time, tFilter

The duration of the explicit and implicit levels on the buses of CAN_H and CAN_L, which is used to monitor whether the activity on the CAN bus is effective.

3 General Requirements of Physical Layer

The physical layer shall provide services for exchanging data bits between two peer media to access control sublayers; which include physical layer signaling data requests and physical layer signaling data indications.

The physical layer signaling data request service is sent from media access control sublayer to the physical layer, requesting the transmission of an explicit or implicit bit.

The physical layer signaling data indication service is sent from physical layer to the media access sublayer, indicating the arrival of an explicit or implicit bit.

3.3 Interface between physical layer signaling and physical media attachment

3.3.1 Message from physical layer signaling to the physical media attachment

When the physical layer signaling receives a signal from the physical medial accessories, the physical layer signaling shall sent an explicit or implicit output message to the physical media attachment.

When physical layer signaling receives a bus close request, the physical layer signaling shall send a bus close message to the physical media attachment.

When physical layer signaling receives the bus close and release request, the physical layer signaling shall send a bus close and release message to the physical media attachment.

3.3.2 Message from physical media attachment to physical layer signaling

When the media access unit receives a bit from the media; the physical media attachment shall send an input message to the physical layer signaling. Such input message represents the arrival of an explicit or implicit bit to the physical layer signaling.

4 Physical Layer Signaling

4.1 Bit encoding and decoding

4.1.1 Bit time

The bus management functions realized within one-bit time, including CAN node synchronization, network transmission delay compensation, sampling point positioning, all of which shall be performed in accordance with programmable bit timing logic; such logic is given by the CAN integrated circuit.

The nominal bit time is divided into 4 non-overlapping time segments, as shown in Figure 2. […]

4.2.2 Phase error of synchronization edge

The phase error of synchronization edge, e, is related to the synchronization segment; which is measured with time slice as the unit. The sign definition of phase error is as follows.

a) When the trip edge falls within the synchronization segment, e = 0;

b) When the trip edge falls before the sampling point, e > 0;

c) When the trip edge falls behind the sampling point, e < 0.

4.2.3 Hard synchronization

After hard synchronization, the bit timing logic unit shall restart the bit time from the synchronization segment. Therefore, the hard synchronization shall force the trip edge that caused the hard synchronization to be within the synchronization segment that starts to restart the bit time.

4.2.4 Resynchronization

When the phase error amplitude of the trip edge that causes the resynchronization is less than or equal to the setting value of the resynchronization jump width, the resynchronization shall lengthen or shorten the bit time to ensure the correct sampling point position. When the phase error amplitude is greater than the resynchronization jump width.

--- If the phaser error, e, is positive, then phase buffer segment 1 shall be increased the value equal to the resynchronization jump width;

--- If the phaser error, e, is negative, then the phase buffer segment 2 shall be shortened the value equal to the resynchronization jump width.

6 High-Speed Media Access Unit with Low Power Mode

6.1.3 Wake-up to exit the low power mode

When it is in the low power mode, physical layer shall monitor the CAN_H and CAN_L of the CAN bus for wakeup. When the bus appears one or more consecutive explicate bus level that can last for at least twake time; and when separated by an implicate bus level, then the bus wakeup shall be performed.

6.1.4 Power-off node system

In order not to affect the CAN communication system, for the actively powered off node (e.g.. ignition key control module), the power-off node shall not affect the bus level as much as possible, when other nodes remain the normal communication. The transceiver shall produce the lowest leakage current to the bus that is still communicating.

Based on the application objectives, the node that is continuously powered shall allow the maximum leakage current parameter defined in Table 13; and the node that is temporarily unpowered shall minimize the leakage current as much as possible.

6.2 Electrical technical requirements

6.2.1 Physical media attachment

In the operating condition of each CAN node, it shall satisfy the parameters specified in Table 12 ~ Table 15.

6.2.3 Technical requirements of medial attachment interface and connector

The Parameters of connector that connect the CAN node to the node on the bus shall be the same as that of Table 7.

6.2.4 Physical media

The technical requirements of physical media attachments are as specified in 5.2.5.

7 High-Speed Media Access Unit with Selective Wake-up Function

7.1 Electrical technical requirements

7.1.1 Physical media attachment

The technical requirements of physical media attachment are as specified in 5.2.2 and 6.2.1. […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 27 pages — is available in the English PDF.

Similar standards

How to Download GB/T 36048-2018

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
27 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 36048-2018

$125.00