GB/T 34444-2017Paper and board—Determination of the layer peel strength (English PDF)
纸和纸板 层间剥离强度的测定
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 34444-2017 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 29, 2017
Implementation date
April 1, 2018
Scope
GB/T 34444-2017 is the English-translated version of 纸和纸板 层间剥离强度的测定.
GB/T 34444-2017 is the Chinese standard "Paper and board—Determination of the layer peel strength". Its scope clause reads: This standard specifies the test method for measuring the peel strength between layers of paper and paperboard.
This standard applies to the determination of a variety of Lin Mozhi, composite paper and cardboard thickness greater than 0.5mm layer of peel strength, does not apply to corrugated cardboard.
Its clauses include principle; equipment; sample; temperature and humidity treatment; sample preparation.
Found what you need?
Document preview — GB/T 34444-2017
National Standard of the People's Republic of China
- ICS
- 85.060
- Classification
- Y 30
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 principle
- 4 equipment
- 5 sample
- 6 temperature and humidity treatment
- 7 Sample Preparation
1 Scope
This standard specifies the test method for measuring the peel strength between layers of paper and paperboard.
This standard applies to the determination of a variety of Lin Mozhi, composite paper and cardboard thickness greater than 0.5mm layer of peel strength, does not apply to corrugated cardboard.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 450 paper and cardboard samples taken and the vertical and horizontal, positive and negative determination
GB/T 10739 Standard atmospheric conditions for the handling and testing of paper, board and pulp specimens
Determination of tensile strength of paper and board GB/T 12914-2008
3 principle
One end of the sample is peeled off in advance by a certain length, and the peeled part is sandwiched between the two ends of the tensile strength testing machine respectively. At a predetermined speed
Degree of peel force was applied to record the peel force curve during peel, calculate the average peel force within the specified chuck displacement.
4 equipment
Tensile strength testing machine shall comply with the requirements of 5.2.1 of GB/T 12914-2008 and equipped with peel force curve recording device. recording
Device should be able to record the chuck displacement from 0mm ~ 150mm peel force curve, and with data acquisition and processing software, data acquisition
The frequency shall ensure that at least 100 data are collected between 25 mm and 125 mm from the chuck and the data processing software shall be capable of peeling
25mm chuck displacement before and after the test data removed, and can calculate the average chuck chuck displacement from 25mm ~ 125mm
The peel strength was calculated using the average peel force.
5 sample
According to GB/T 450 provisions for sampling.
6 temperature and humidity treatment
Samples should be GB/T 10739 temperature and humidity treatment, and in this atmospheric conditions to prepare samples and test.
Note. Under normal circumstances, the temperature and humidity treatment time of 24h, quantitative high, thick cardboard can be properly extended processing time.
7 Sample Preparation
7.1
The specimen shall not be cut within 15 mm of the edge of the cardboard and shall not be creased, […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 34444-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 34444-2017
$85.00