Valid

GB/T 34422-2017Brake disc for automobile (English PDF)

汽车用制动盘

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 34422-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

October 14, 2017

Implementation date

May 1, 2018

Scope

GB/T 34422-2017 is the English-translated version of 汽车用制动盘.

GB/T 34422-2017 is the Chinese standard "Brake disc for automobile". Its scope clause reads: This Standard specifies the terms and definitions, classification, technical requirements, inspection methods of brake disc for automobile (hereinafter referred to as “brake disc”).

This Standard applies to brake disc used for M and N class automobile brakes specified in GB/T 15089-2001 of which the body material is gray cast iron. The brake disc made of other material shall refer to this for implementation. Its clauses include terms and definitions; inspection method.

Found what you need?

Document preview — GB/T 34422-2017

National Standard of the People's Republic of China

ICS
43.040.40
Classification
T 24

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • 1 Scope4
  • 2 Normative references4
  • 3 Terms and definitions5
  • 4 Classification6
  • 5 Technical requirements7
  • 6 Inspection method11
  • Annex A (Normative) Brake disc bench test method13

1 Scope

This Standard specifies the terms and definitions, classification, technical requirements, inspection methods of brake disc for automobile (hereinafter referred to as “brake disc”).

This Standard applies to brake disc used for M and N class automobile brakes specified in GB/T 15089-2001 of which the body material is gray cast iron. The brake disc made of other material shall refer to this for implementation.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 223.3, Methods for chemical analysis of iron, steel and alloy - The diantipyrylmethane phosphomolybdate gravimetric method for the determination of phosphorus content

GB/T 223.58, Methods for chemical analysis of iron, steel and alloy - The extraction-absorption catalytic polarographic method for the determination of manganese content

GB/T 223.59, Iron, steel and alloy - Determination of phosphorus content-

Bismuth phosphomolybdate blue spectrophotometric method and antimony phosphomolybdate blue spectrophotometric method

GB/T 223.60, Methods for chemical analysis of iron, steel and alloy - The perchloric acid dehydration gravimetric method for the determination of silicon content

GB/T 223.62, Methods for chemical analysis of iron, steel and alloy; The butyl acetate extraction photometric method for the determination of phosphorus content

GB/T 223.63, Methods for chemical analysis of iron, steel and alloy - The sodium (potassium) periodate photometric method for the determination of manganese content

GB/T 231.1, Metallic materials - Brinell hardness test - Part 1: Test method

GB/T 1031, Geometrical product specifications(GPS) - Surface texture:

Profile method - Surface roughness parameters and their values

GB/T 1958, Geometrical product Specifications (GPS) - Geometrical tolerance - Verification prescription

GB/T 3177, Inspection of plain workpiece sizes

GB/T 7216, Hygienic requirements for peacetime utilization of civil air defence works

GB/T 9239 (all parts), Balance quality of rigid rotors - Determination of permissible residual unbalance

GB/T 9439, Grey iron castings

GB/T 15089-2001, Classification of power-driven vehicles and trailers

GB/T 20123, Steel and iron - Determination of total carbon and sulfur content

Infrared absorption method after combustion in an induction furnace

QC/T 556, Automotive brake temperature measurement and thermocouple mounted

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

3.1 ventilated disc

the brake disc with a ventilation duct between two friction surfaces

3.2 solid disc

the brake disc without a ventilation duct between two friction surfaces

3.3 mounting surface

the surface mounted on the hub and fitted with the hub; the mounting reference surface of brake disc

3.4 disc thickness variation; DTV

the variation of the thickness of two friction surfaces on either circumference

3.5 minimum thickness

5.10.1.2

M 2 , M 3 , N2 and N3 vehicle brake disc samples shall be tested

according to A.4.1.1. It shall meet the following requirements:

a) the number of thermal fatigue test cycles at the failure of the brake disc sample is greater than or equal to 15, or b) when the number of cycles of thermal fatigue test on the failure of a brake disc sample is more than 10 but less than 15, then use a new sample of the brake disc for test.

5.10.2 High-load test

The brake disc sample shall not be invalid after it completes the high-load test according to A.4.2.

6 Inspection method

6.1 Mechanical properties

6.1.1 Wedge pressure strength

Wedge sample size shall comply with the provisions of Table 6. The inspection methods are in accordance with the provisions of GB/T 9439. Take the average value of three wedge pressure strengths.

Table 6 -- Wedge sample requirements

Thickness mm

Width mm

Length mm

Flatness mm

Roughness Ra

µm

6.0±0.1 20

>=20, the same sample can be tested many times

0.1 <=1.6

6.1.2 Friction surface hardness

The test site of brake disc friction surface hardness shall be in the middle of the friction surface. Test at least 3 points evenly along with circumference. The hardness of ventilated disc shall be tested on the friction surface right above the rib. The test method is in accordance with GB/T 231.1.

6.2 Chemical composition

The test method for chemical composition is in accordance with Table 7. It may use other methods. But the test method used shall be indicated in the test report.

A.2.3 Cooling wind speed

Test without the wheel. During braking, or between two braking, the cooling wind speed shall be limited to V air = 0.33V0 (V0 is the vehicle speed at the start of braking). The wind speed in other cases is not limited.

Cool air to room temperature.

A.2.4 Boost rate, buck rate of brake pressure

The boost rate, buck rate of brake line pressure of test equipment shall meet the following requirements.

a) Air brake is 1.5 MPa/s ± 0.3 MPa/s;

b) Hydraulic brake is 25 MPa/s ± 5 MPa/s.

A.2.5 Sampling rate

The sampling rate of brake line pressure and braking torque shall be greater than 20Hz.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 34422-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 34422-2017

$125.00