GB/T 34028-2017Valve stem reciprocating seals of engine and performance test method (English PDF)
发动机气门导杆往复油封及性能试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 34028-2017 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 12, 2017
Implementation date
February 1, 2018
Scope
GB/T 34028-2017 is the English-translated version of 发动机气门导杆往复油封及性能试验方法.
GB/T 34028-2017 is the Chinese national standard for the valve stem reciprocating seal of an engine and for its performance test method.
It specifies the basic structure, the parameter code and the marking, the requirements, the inspection rules and the provisions on marking, packaging, transport and storage of the valve guide reciprocating oil seal, which it calls the valve seal.
It applies to the valve guide reciprocating oil seals of petrol and gas engines. The basic structure of the valve seal is made of the mounting support, the lip, the skeleton and a spring, or no spring at all.
It cites GB/T 531.1-2008, GB/T 1682-2014, GB/T 1690-2010, GB/T 2828.1-2012, GB/T 2941-2006, GB/T 5721-1993 and GB/T 7759.1-2015. It carries ICS 83.140.50 and Chinese classification G43, was issued on 12 July 2017 and has applied since 1 February 2018.
Found what you need?
Document preview — GB/T 34028-2017
National Standard of the People's Republic of China
- ICS
- 83.140.50
- Classification
- G 43
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Basic structure, parameter code and mark
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This standard specifies the basic structure of the valve guide reciprocating oil seal (hereinafter referred to as "valve seal"), the parameter code and mark, to Seeking, inspection rules, signs, packaging, transportation and storage.
This standard applies to fuel and gas engine valve guide reciprocating oil seal.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 528 Rubber, vulcanized or thermoplastic - Determination of tensile stress - strain properties
GB/T 531.1-2008 vulcanized rubber or thermoplastic rubber test methods into the hardness - Part 1: Shore Hardness Tester (Shao Hardness)
GB/T 1682-2014 Rubber, vulcanized - Determination of low temperature brittleness - Single - sample method
GB/T 1690-2010 Test method for fluid resistance of vulcanized rubber or thermoplastic rubber
GB/T 2828.1-2012 Sampling procedures for inspection - Part 1 - Batch-by-lot inspection by acceptance quality limit (AQL) plan
GB/T 2941-2006 Rubber physical test methods - General procedure for the preparation and conditioning of test specimens
GB/T 3512 Vulcanized rubber or thermoplastic rubber - Accelerated aging and heat resistance tests on hot air
GB/T 5721-1993 rubber seal product marking, packaging, transport and storage of the general provisions
GB/T 7759.1-2015 Rubber, vulcanized or thermoplastic - Determination of compression set - Part 1: at room temperature and high temperature
3 Basic structure, parameter code and mark
3.1 The basic structure
3.1.1 The basic structure of the valve seal by the installation of support, lip, skeleton, spring (or no spring) composition, shown in Figure 1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 528Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties
- GB/T 531.1-2008Rubber, vulcanized or thermoplastic -- Determination of indentation hardness -- Part 1: Durometer method (Shore hardness)
- GB/T 1682-2014Vulcanized rubber - Determination of low-temperature brittleness - Single test piece method
- GB/T 1690-2010Rubber, vulcanized or thermoplastic—Determination of the effect of liquids
- GB/T 2828.1-2012Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
- GB/T 2941-2006Rubber - General procedures for preparing and conditioning test pieces for physical test methods
Similar standards
How to Download GB/T 34028-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 1682-2014 — Vulcanized rubber - Determination of low-temperature brittleness - Single test piece method
GB/T 1690-2010 — Rubber, vulcanized or thermoplastic—Determination of the effect of liquids
GB/T 2828.1-2012 — Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
Secure payment via Stripe
Payments accepted
GB/T 34028-2017
$145.00