Valid

GB/T 33908-2017Technical specification for testing of liquidus temperature of the electrolyte (English PDF)

铝电解质初晶温度测定技术规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 33908-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

July 12, 2017

Implementation date

June 1, 2018

Scope

GB/T 33908-2017 is the English-translated version of 铝电解质初晶温度测定技术规范.

GB/T 33908-2017 fixes how the primary crystal temperature (liquidus temperature) of an aluminium electrolyte is measured by the step cooling curve method, over the range 800 C to 1000 C. It sets the basic requirements for the measurement, the identification of the inflection point of the primary crystal temperature and the cooling speed.

It defines the primary crystal temperature and the step cooling curve method, and prescribes the sampling and sample preparation: the electrolyte is sampled in the cell according to Annex A, crushed and ground to pass a 75 micrometre standard screen, then pre-dried in an oven at 110 C plus or minus 5 C for at least 3 hours and kept in a desiccator.

It also fixes the measurement cycle, normally 15 days and shortened when new electrolyte types are added, when anode effects become frequent and unstable, or after the cell is restarted following an overhaul, and it lists the auxiliary equipment, including the oven, the analytical balance readable to 0.01 g, the melting crucible of special corundum or heat-resistant stainless steel sized about 20 mm by 70 mm, and the crushing and grinding equipment. It was issued on 12 July 2017 and has applied since 1 June 2018.

Found what you need?

Document preview — GB/T 33908-2017

National Standard of the People's Republic of China

ICS
71.100.10
Classification
H 21

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Terms and definitions
  • 3 Aluminum electrolytic sampling and sample preparation of the general requirements
  • 4 Determination of cycle and equipment selection

Foreword

This standard is drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This standard specifies the basic requirements of the initial crystallization temperature of the electrolyte and the speed of the sample during the measurement. The identification of the inflection point of the primary crystal temperature And cooling speed and other technical requirements.

This standard is suitable for the determination of the initial crystallization temperature of aluminum electrolytes by step cooling curve method. The measurement range is 800 ° C to 1000 ° C.

2 Terms and definitions

The following terms and definitions apply to this document.

2.1 Primary crystal temperature

The temperature at which the electrolyte begins to crystallize is also considered to be the temperature at which the aluminum electrolyte begins to convert from a liquid state to a solid state.

2.2 Step - down curve method

The method of measuring the primary crystallization temperature of the aluminum electrolyte is determined by first-step cooling of the aluminum electrolyte sample under the prescribed conditions, and then recording The entire cooling curve has a stagnant period (inflection point).

3 Aluminum electrolytic sampling and sample preparation of the general requirements

3.1 The aluminum electrolyte sample is sampled in the cell according to Appendix A.

3.2 Sampling After crushing and grinding to all through a 75 µm standard screen.

3.3 The samples are pre-dried in an oven at 110 ° C ± 5 ° C for at least 3 hours, taken out and stored in a desiccator.

4 Determination of cycle and equipment selection

4.1 Determination of the cycle

Should be determined according to the production of enterprises, usually 15 days. With one of the following conditions, should be appropriate to shorten the initial crystal temperature measurement cycle.

a) the recent addition of different types, components of the electrolyte;

b) the recent anode effect of the electrolytic cell is more frequent and unstable than the original;

c) The cell is restarted after overhaul.

4.2 Auxiliary equipment

4.2.1 Oven. temperature can be controlled at 110 °C ± 5 °C.

4.2.2 Analysis of the balance. the amount of 0.01g.

4.2.3 melting crucible. the choice of a certain resistance to fluoride corrosion of the material, should use special corundum or heat-resistant stainless steel, stainless steel crucible The size of the cup should be phi20 × 70mm. The molten sample can be contained and does not react with the sample.

4.2.4 Crushing and grinding equipment. mainly including jaw crusher, grinding machine, the electrolyte can be crushed and ground to all through the 75µm Standard screen.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 33908-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 33908-2017

$145.00