Valid

GB/T 33738-2017Mobile Payment—Technical requirements for intellegent card based on 2.45GHz RRC(range controlled communication) technology (English PDF)

手机支付基于2.45GHz RCC（限域通信）技术的智能卡技术要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (28 pages)

Need quotation for your management?

Get a formal quotation for GB/T 33738-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

May 12, 2017

Implementation date

December 1, 2017

Scope

GB/T 33738-2017 is the English-translated version of 手机支付基于2.45GHz RCC（限域通信）技术的智能卡技术要求.

GB/T 33738-2017 fixes the technical requirements for a smart card used in mobile payment over 2.45 GHz RCC, range controlled communication.

It covers the hardware architecture in single-module and dual-module form, the software architecture, the physical characteristics with the geometry of the PLUG-IN, RF-MiniSIM and RF-NanoSIM card and card base, and the electrical characteristics with the voltage and current limits including idle and clock-stop mode.

It then covers the contact and contactless interfaces, the RF communication success rate, immunity to Bluetooth, WiFi and 13.56 MHz signals, concurrent handling of data on the two interfaces, multi-application support and security, the CIOS/COS APDU and TPDU interfaces and the security module.

It cites GB/T 33736, three YD/T documents, ISO/IEC 7816-1, -2 and -3 and ETSI TS 102 221 V8.3.0. It was issued on 12 May 2017 and has applied since 1 December 2017.

Found what you need?

Document preview — GB/T 33738-2017

National Standard of the People's Republic of China

ICS: 33.050.99
Classification: M 32

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Preface
Introduction
1 Scope
2 normative reference document
3 Terms and definitions
4 acronym
5 based on the 2.45GHzRCC (limited field communication) technology, the overall technical requirements of smart cards
5.1 Overview
5.2 Hardware architecture
5.2.1 Architectural overview
5.2.2 Single module structure (SME)
5.2.3 Dual Module Architecture (DME)
5.3 Software Architecture
6 Physical properties
6.1 General Physical Characteristics
6.2 format and layout
6.2.1 Minimum contact area
6.2.2 PLUG-IN card geometry
6.2.3 RF-MiniSIM card and card base geometry
6.2.4 RF-NanoSIM card and card base geometry
6.2.5 Contact assignment
7 Electrical characteristics
7.1 Description of electrical signals
7.2 Voltage and current
7.2.1 Voltage Limits
7.2.2 Limitation of operating current
7.2.3 Free current limit
7.2.4 Idle mode current limit at full frequency
7.2.5 Current limit for clock stop mode
7.2.6 Voltage and current characteristics of I/O, CLK, RST
8 communication interface characteristics
8.1 Contact communication interface
8.2 Non-contact communication interface
8.2.1 General requirements for non-contact communication interfaces
8.2.2 RF communication success rate
8.2.3 Anti-interference with Bluetooth signals
8.2.4 Anti-interference to WiFi signal
8.2.5 Anti-interference to 13.56MHz signal (optional)
8.3 Interface data concurrency processing
8.3.1 interface data concurrency
8.3.2 Concurrent processing requirements
8.4 Multi-application support
8.4.1 Application of multiple technical requirements
8.4.2 Multi-application security
9 CIOS/COS Architecture Interface Management
9.1 Overview of CIOS interfaces
9.2 APDU interface
9.3 TPDU interface
10 Technical requirements for safety modules
10.1 Hardware Requirements
10.2 Hardware Security Requirements
10.3 CIOS/COS Software Security Requirements
10.4 Data security requirements
10.5 Access Control Security Requirements
10.6 Transaction Protection Mechanism (Transaction)
10.7 Multi-application management protocol requirements
Appendix A (normative) CIOSAPDU interface
A.1 CIOS interface
A.1.1 Set_Boot
A.1.2 Get_Ver
A.1.3 RF_Start
A.1.4 RF_Send
A.1.5 RF_Status
A.1.6 Get_ICID
A.1.7 SIM_APDU_Transmit
A.2 HOOK interface
A.2.1 COSFun_Param_Init
A.2.2 RF_APDUData_Process_Function
A.2.3 Check_OutgoingData_Hook
A.2.4 Find_7816APDU_Instruction
A.2.5 Get_7816APDU_Instruction_Description
A.2.6 Monitor_IncomingAPDU_Instruction
A.2.7 Exec_COS_Instruction
A.2.8 Cos_process_instruction_not_in_table
Appendix B (normative) CIOSTPDU interface
B.1 System Interface
B.1.1 ISO 7816VMInit
B.1.2 7816S_RecvByte
B.1.3 7816S_SendByte
B.1.4 GetSIMResponse
B.1.5 CosBridge
B.2 Hook interface
B.2.1 ISO 7816_VM
Appendix C (informative) CIOS/COS Technical Characteristics
C.1 operating mechanism
C.1.1 Working status description
C.1.2 Power-up status
C.1.3 Sleep state
C.1.4 RF processing status
C.1.5 7816 Processing Status
Appendix D (informative) COS development and interface use example
D.1 based on CIOSAPDU interface development example
D.1.1 7816 Application Development
D.1.2 RF Application Development
D.2 CIOSTPDU interface usage example

Foreword

This standard is based on 2.45GHzRCC (limited field communication) technology, and based on 13.56MHz and 2.45GHz dual-band technology mobile phone Pay one of the series of standards. The series of standards include.

--- mobile phone payment based on 2.45GHzRCC (limited field communication) technology of non-contact RF interface technology requirements;

--- mobile phone payment based on 2.45GHzRCC (limited field communication) technology, smart card technology requirements;

--- mobile phone payment based on 2.45GHzRCC (limited field communication) technology of non-contact reader terminal technical requirements;

--- 13.56MHz and 2.45GHz dual-band technology based on non-contact reader RF interface technology requirements;

--- mobile phone payment based on 2.45GHzRCC (limited field communication) technology, non-contact RF interface test method;

--- mobile phone payment based on 2.45GHzRCC (limited field communication) technology, smart card test method;

--- Mobile payment based on 2.45GHzRCC (limited field communication) technology of non-contact reader terminal test method;

--- Realization of RF Interface Test Method for Contactless Readers Based on 13.56MHz and 2.45GHz Dual Frequency Technology.

This standard is drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This standard specifies smart card technology requirements based on 2.45GHz RCC (limited field communication) technology, including smart card hardware and software Structure, physical characteristics, electrical characteristics, communication interface, multi-application support, security module requirements, and application development interface and so on.

This standard applies to smart cards that support technology based on 2.45 GHz RCC (limited field communication).

2 Normative reference documents

The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this document. For undated references, the latest edition (including all modifications) applies to this document.

GB/T 33736 mobile payment based on 2.45GHzRCC (limited field communication) technology of non-contact RF interface technical requirements

YD/T 1762.1-2016 TD-SCDMA/WCDMA digital cellular mobile communication network universal integrated circuit card (UICC) Technical requirements for Cu interfaces with terminals - Part 1: Physical, electrical and logical characteristics

YD/T 2501-2013 Safety Requirements for Mobile Phone Payment Smart Card and Built - in Security Module

YD/T 3247-2017 Technical requirements for multi - application management protocols for mobile payment

ISO/IEC 7816-1:2011 Identification of integrated circuit cards with contacts - Part 1: Physical characteristics (cards-Integratedcircuit (s) cardswithcontacts-Part 1. Physicalcharacteristics)

ISO/IEC 7816-2:2007 Identification of integrated circuit cards with contacts Part 2: Dimensions and positioning of contacts (Identifica-assigncards-integratedcircuit (s) cardswithcontacts-Part 2. Dimensionsandlocationofthecontacts)

ISO/IEC 7816-3:2006 Identification of integrated circuit cards with contacts - Part 3: Signals and transport protocols (Identifica-tioncards-Integratedcircuit (s) cardswithcontacts-Part 3. Electronicsignalsandtransmissionpro-tocols)

ETSI TS 102 221 V8.3.0 Smart Card UICC Terminal Interface Physical and Logical Features (SmartCards; UICC-Ter-minalinterface; Physical andlogicalcharacteristics)

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 2.45GHz smart card

Based on 2.45GHz RCC (limited field communication) technology, smart cards, including RF- (U) SIM card, RF-MiniSIM card, RF- NanoSIM card.

3.2 Card IO management system

Card middleware software module, to achieve RF RF channel and 7816 interface, the underlying hardware interface management and data concurrent processing, and for The upper layer COS provides API interface management.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 28 pages — is available in the English PDF.

Referenced standards

Normative references

ISO/IEC 7816-1 · ISO/IEC 7816-2 · ISO/IEC 7816-3 · ETSI TS 102 221 V8.3.0

Cited by

GM/T 0064-2018Cryptography test requirements for range controlled communication (RCC)

Similar standards

GB/T 38624.3-2024|GB/T 38624.2-2021|GB/T 33736-2017|GB/T 33737-2017|GB/T 33739-2017|GB/T 33740-2017

How to Download GB/T 33738-2017

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.