Valid

GB/T 33518-2017Remanufacturing—Based on spectral analysis to detect assessment specification shaft parts (English PDF)

再制造 基于谱分析轴系零部件检测评定规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 33518-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

February 28, 2017

Implementation date

June 1, 2017

Scope

GB/T 33518-2017 is the English-translated version of 再制造 基于谱分析轴系零部件检测评定规范.

GB/T 33518-2017 sets out how remanufactured shaft parts are inspected and assessed using power spectrum analysis.

The inspection requirements come in groups: material testing, which for metal parts covers mechanical properties, heat treatment, surface stress, fatigue life, physical and chemical tests, non-destructive testing and weld grade, and for non-metallic parts ageing and damage; machining inspection of the main dimensions, the geometric tolerances and the roughness of finished parts and of bought-in parts; and inspection of assemblies for fitting dimensions and clearances, radial, axial and angular compensation, torque, speed and dynamic balance.

Test objects are sorted into sound, damaged and remanufactured parts, recorded one by one, and then run on a test bench for power spectrum measurement. It applies to couplings, expansion joints and other shaft parts. Issued on 28 February 2017, it has applied since 1 June 2017.

Found what you need?

Document preview — GB/T 33518-2017

National Standard of the People's Republic of China

ICS
21.120.20
Classification
J 19

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Detection requirements

Foreword

This standard is drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This standard specifies the detection requirements, power spectrum analysis and evaluation specifications of remanufactured shaft parts (hereinafter referred to as "parts").

This standard applies to couplings, expansion joints and other shaft parts.

2 Detection requirements

2.1 Material testing

2.1.1 mechanical properties of metal parts, heat treatment requirements, surface stress testing, fatigue life testing, physical and chemical testing, non-destructive testing and welding Seam level and other items of the test should be the appropriate standard or manufacturing requirements of the drawings to detect the degree of non-compliance.

2.1.2 non-metallic materials, parts of the performance and defects should be detected according to the appropriate standards or manufacturing requirements, to detect its aging or Damage level.

2.2 Processing inspection

2.2.1 The major dimensions of the finished parts, the deviation of the geometric tolerances and the roughness values shall be measured in accordance with the requirements of the corresponding standards or manufacturing drawings. Line, to detect its wear and deformation.

2.2.2 The performance of the purchased parts and the quality of the test should be carried out according to the requirements of the corresponding standards to detect the degree of its function.

2.3 Assembly parts detection

2.3.1 The installation dimensions, dimensions and clearance of the assembly parts shall be tested in accordance with the requirements of the manufacturing assembly drawing, And the degree of compliance with the deviation.

2.3.2 Assembling parts Radial, axial and angular compensation quantities shall be tested in accordance with the requirements of the corresponding standards or manufacturing assembly drawings, Integrated wear and deformation.

2.3.3 Assembly parts Torque, speed and dynamic balance level of the test should be the appropriate standard or manufacturing assembly requirements of the requirements, to test its bearing Performance and balance of the degree of compliance.

2.4 Parts status

2.4.1 The test object is divided into qualified parts and damaged parts, as well as remanufactured parts. Qualified parts are in accordance with 2.1 ~ 2.3 of the provisions of the test, in full compliance with the corresponding standards or manufacturing requirements of the drawings; damaged parts are simulated in the actual use of the failure State, some of its test items do not meet the conditions specified in 2.1 to 2.3; remanufacturing parts are based on the failure of the repair, its satisfaction Original function and use, even in the performance of the upgrade.

2.4.2 Damaged parts need to be marked on the destruction of the one by one, and record the damage; remanufacturing parts need to repair Line one by one, and for repair records.

2.5 Power spectrum detection

2.5.1 qualified parts, damaged parts and remanufactured parts are required to be tested on the test bench, the determination of various parts of the work

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 33518-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 33518-2017

$65.00