Valid

GB/T 33434-2016Determination of fume emission rate during arc welding of shipbuilding (English PDF)

船舶电弧焊烟尘排放率测定方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 33434-2016 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 30, 2016

Implementation date

July 1, 2017

Scope

GB/T 33434-2016 is the English-translated version of 船舶电弧焊烟尘排放率测定方法.

GB/T 33434-2016 fixes the general requirements, the test procedure, the calculation of results and the test report for measuring the fume emission rate of arc welding in shipbuilding.

Clause 1 applies the standard to the determination, under laboratory conditions, of the fume emitted during welding and of the fume emitted by the electrode.

Clause 2 defines the vocabulary used for the measurement, naming fume as the smoke or dust produced during welding, the fume emission rate as the quantity of fume generated per unit of time, and fume emission as the quantity produced per 100 g of deposited metal.

Clause 3 covers the general requirements, starting with the ambient conditions, which call for room temperature and a relative humidity of no more than 75%.

The same clause lists the instruments needed and the accuracy each must reach: a clamp meter for welding current and voltage, a stopwatch with an error below 0.1 s, a measuring block for dry elongation with an error below 1 mm, a balance reading to 1 mg, a gas flowmeter with an error below 1 L/min and a hygrometer for temperature and humidity, all of which must be within their calibration validity.

Clause 3 then turns to the test equipment, specifying a semi-closed device made of thin steel plate whose internal surfaces are to be smooth so that fume does not settle on them.

The standard was proposed by the China Shipbuilding Industry Corporation, falls under the National Technical Committee on Marine Ships (SAC/TC 12), and was drafted with shipyard, research institute and welding consumable industry participation. It was issued on 30 December 2016 and has applied since 1 July 2017.

Found what you need?

Document preview — GB/T 33434-2016

National Standard of the People's Republic of China

ICS
47.020.01
Classification
U 06

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Terms and definitions
  • 3 General requirements

Foreword

This standard is drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This standard specifies the general requirements, test procedures, calculation results and test reports for the determination of soot emission rate of ship arc welding.

This standard is applicable to the determination of the welding exhaust emissions and the soot emission of the electrode under the laboratory environment.

2 Terms and definitions

The following terms and definitions apply to this document.

2.1 Soot

The smoke or dust produced during the welding process.

2.2 Soot emission rate

The amount of smoke generated per unit of time.

2.3 Emissions of smoke

The amount of dust produced per 100g of deposited metal.

3 General requirements

3.1 Environmental conditions

The environmental conditions for the determination of the emissions of soot and soot emissions shall meet the following requirements.

a) Ambient temperature is room temperature;

b) relative humidity not more than 75%.

3.2 Measuring instruments and meters

Determination of arc welding dust emission rate, soot emissions of the instrumentation include.

a) measure the welding current, voltage clamp table;

b) record the time of the stopwatch, the measurement error is less than 0.1s;

c) dry elongation measurement block, the measurement error is less than 1mm;

d) weighing the balance, the measurement accuracy of 1mg;

e) gas flowmeter, the measurement error is less than 1L/min;

f) hygrometer for measuring temperature and humidity.

The above instruments should be met and qualified within the validity period.

3.3 Test equipment

3.3.1 Test device

The test device is a semi-closed device made of thin steel plate, the internal surface should be smooth, to avoid the deposition of smoke. The sharp corners within the device

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 33434-2016

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 33434-2016

$205.00