Valid

GB/T 33112-2016Verification method of instruments devoted to geotechnical engineering prototype monitoring (English PDF)

岩土工程原型观测专用仪器校验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (27 pages)

Need quotation for your management?

Get a formal quotation for GB/T 33112-2016 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

October 13, 2016

Implementation date

May 1, 2017

Scope

GB/T 33112-2016 is the English-translated version of 岩土工程原型观测专用仪器校验方法.

GB/T 33112-2016 is the Chinese standard "Verification method of instruments devoted to geotechnical engineering prototype monitoring".

Its scope clause reads: This standard specifies the verification of field calibration and field calibration for special instruments for geotechnical engineering prototyping (hereinafter referred to as "prototype observation instruments") Parameter requirements, calibration conditions, calibration items and calibration methods.

This standard applies to differential resistors, vibrating wire, potentiometer, photoelectric (CCD), stepper motor and capacitive prototype observation equipment Of the check.

Its clauses include normative reference documents; terms and definitions; general.

Found what you need?

Document preview — GB/T 33112-2016

National Standard of the People's Republic of China

ICS
07.060
Classification
P 10

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 5 check parameter requirements
  • 5.1 Calibration parameter classification
  • 5.2 Indoor calibration
  • 5.3 Field Verification
  • 6 check conditions
  • 6.1 Environmental conditions
  • 6.2 calibration equipment
  • 7 check items and calibration methods
  • 7.1 Indoor calibration items and calibration methods
  • 7.2 Field calibration items and calibration methods
  • 8 check results and check cycle
  • 8.1 Verification Results
  • 8.2 Verification cycle
  • Appendix A (informative) Differential Resistive Instrument Indoor Check Record Table
  • Appendix B (informative appendix) Vibrating wire type instrument indoor calibration record table
  • Appendix C (informative) Potentiometer Instrument Laboratory Verification Record Table
  • Appendix D (informative) Photocopical record of photoelectric type (CCD) instrument
  • Appendix E (informative) Manual checklist for stepper motor equipment
  • Appendix F (informative appendix) Capacitive instrument indoor calibration record table
  • Appendix G (informative) Temperature measurement instruments Laboratory checklist
  • Appendix H (informative) Differential Resistive Instrument Field Verification Record Table
  • Appendix J (informative) Potentiometer Verification Record Table
  • Appendix K (informative) Photoelectric type (CCD) type/stepper motor type field check record table
  • Appendix L (Informative Appendix) Capacitive Instrument Field Verification Record Table
  • Appendix N (Informative Appendix) Instrumentless Field Verification Record Table
  • Appendix O (informative) Recorded recording of pressure instruments in pressurized pressure
  • Appendix P (Informative Annex) Static Level Verification Record Table
  • Appendix Q (informative) Vertical calibration table
  • Appendix S (informative) Verification Report Cover
  • Appendix T (informative) Verification report title page

1 Scope

This standard specifies the verification of field calibration and field calibration for special instruments for geotechnical engineering prototyping (hereinafter referred to as "prototype observation instruments")

Parameter requirements, calibration conditions, calibration items and calibration methods.

This standard applies to differential resistors, vibrating wire, potentiometer, photoelectric (CCD), stepper motor and capacitive prototype observation equipment

Of the check.

2 normative reference documents

The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this article

Pieces. For undated references, the latest edition (including all modifications) applies to this document.

GB/T 13606 Geotechnical test equipment Geotechnical engineering equipment Vibrating wire sensor General technical conditions

GB/T 24106 Terminology and symbols for geotechnical engineering instruments

Code for inspection and verification of dam safety monitoring instruments

3 terms and definitions

GB/T 24106 Definitions and the following terms and definitions apply to this document.

3.1 Prototype observation

According to technical regulations, the engineering structure of the traits and changes in the process of dynamic monitoring and observation of technical operations.

3.2 Geotechnical prototyping instrumentation

On the geotechnical engineering structure of the characteristics and changes in the observation of the instrument collectively.

Note. According to the principle of measurement is divided into angle, displacement, pressure, stress, strain and temperature measurement instruments. According to the principle of instrument structure is divided into differential resistive, vibrating wire

Type, potentiometer type, photoelectric (CCD), stepper motor and capacitive instruments. Its working principle is to use the characteristics of the instrument itself to obtain geotechnical engineering

Prototype observations of various parameters.

3.3 Indoor calibration

Under the indoor conditions, the accuracy of the prototype observation equipment, temperature parameters and insulation resistance and other technical indicators of the calibration.

3.4 Field verification

Prototype observation equipment installation/embedded in the engineering entity state, the stability of the instrument measurement, insulation resistance, four-core differential resistance instrument

Positive and negative resistance ratio, than the measurement limit and reset accuracy and other technical indicators of the calibration.

4 General

4.1

Prototype observation equipment and connecting cables should be identified, the name of the instrument, model, the main technical parameters, manufacturer name, factory number and date, etc.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 27 pages — is available in the English PDF.

Similar standards

How to Download GB/T 33112-2016

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
27 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 33112-2016

$475.00