Valid

GB/T 32573-2016Silicon powder - Determination of total carbon content - Infrared absorption method after combustion in an induction furnace (English PDF)

硅粉 总碳含量的测定 感应炉内燃烧后红外吸收法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 32573-2016 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

February 24, 2016

Implementation date

November 1, 2016

Scope

GB/T 32573-2016 is the English-translated version of 硅粉 总碳含量的测定 感应炉内燃烧后红外吸收法.

GB/T 32573-2016 is the Chinese standard "Silicon powder - Determination of total carbon content - Infrared absorption method after combustion in an induction furnace".

Its scope clause reads: This standard specifies the use of induction furnace fume Determination of total carbon content of the infrared absorption method after combustion.

This standard applies to the determination of the production of polysilicon materials in the total carbon content of the silicon powder. Determination of the range of 0.001% to 1.0% (mass fraction). Its clauses include method summary; reagents and materials.

Found what you need?

Document preview — GB/T 32573-2016

National Standard of the People's Republic of China

ICS
29.045
Classification
H 82

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Method summary
  • 4 Reagents and materials

1 Scope

This standard specifies the use of induction furnace fume Determination of total carbon content of the infrared absorption method after combustion.

This standard applies to the determination of the production of polysilicon materials in the total carbon content of the silicon powder. Determination of the range of 0.001% to 1.0% (mass fraction).

2 Normative references

The following documents for the application of this document is essential. For cited documents with dates, only the dated edition applies to this document. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 6379.2-2004 measurement methods and results of Accuracy (trueness and precision) - Part 2. Determine the standard methods of measurement repeatability and reproducibility of the basic method

Laboratory use specifications and test methods GB/T 6682-2008 Analysis

JJG395 Dingtan fixed sulfur analyzer test procedures

YS/T 724-2009 silica fume

YB/T 4145 carbon and sulfur analyzer dedicated crucible

3 Method summary

Sample in a high frequency induction furnace, which leads to oxygen gas stream at high temperature, under the conditions of flux and there is the presence of other additives, and is converted to carbon dioxide and/or carbon monoxide, airflow measurement of carbon dioxide and/or carbon monoxide the infrared absorption spectrum, and thus calculate the carbon content of the test samples.

4 Reagents and materials

4.1 water

before non-carbonated, use complies with GB/T 6682-2008 requirements tertiary water boiled 30min, equipped with a soda lime drying tube rubber-stoppered bottle, cooled to room temperature, pass oxygen (4.2) blow bubble 15min.

4.2 Oxygen

purity (volume fraction) should be not less than 99.5% purity (volume fraction) the determination of carbon content of 0.001% to 0.01% when the sample shall be not less than 99.995%.

4.3 iron

a particle size of not more than 1.25mm, size recommended range 0.4mm ~ 0.8mm, carbon content (mass fraction) should be less than 0.0005%.

Anhydrous sodium carbonate 4.4. certified reference materials, anhydrous sodium carbonate prior to use (mass fraction greater than 99.9%) and dried 2h at 285 °C ± 5 °C, and placed in the dryer to cool and set aside.

4.5 sodium carbonate standard solution

1mL containing 2.50mg carbon. Weigh 5.5152g sodium carbonate (4.4), accurate to 0.1mg, dissolved in 200mL water (4.1) and quantitatively transferred to 250mL volumetric flask with water (4.1) diluted to the mark, and mix.

4.6 tin flux

special carbon and sulfur high-purity tin particles, tin content (mass fraction) should be greater than 99.8%, particle size 0.4mm ~ 0.8mm, carbon content (mass fraction) should be less than 0.0005%.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 32573-2016

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 32573-2016

$145.00