Valid

GB/T 32130-2015DC PLC filter capacitors for HVDC transmission systems (English PDF)

高压直流输电系统用直流PLC滤波电容器

Preview PDF

This is a limited preview

Buy now to download the full PDF (20 pages)

Need quotation for your management?

Get a formal quotation for GB/T 32130-2015 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

October 9, 2015

Implementation date

May 1, 2016

Scope

GB/T 32130-2015 is the English-translated version of 高压直流输电系统用直流PLC滤波电容器.

GB/T 32130-2015 is the Chinese standard "DC PLC filter capacitors for HVDC transmission systems". Its scope clause reads: This standard specifies the HVDC systems Terms and definitions PLC DC filter capacitor, conditions of use, design and construction, to Basic requirements and test, quality and other aspects.

This standard applies to high-voltage direct current (HVDC) transmission system HVDC Converter Station side, installed in the indoor or outdoor DC PLC filter circuit Container for filtering 30kHz ~ 500kHzPLC noise signal in the frequency range to prevent the carrier PLC converter valve noise generated in the frequency domain Along the sound of a communication system noise interference.

HVDC systems commonly filter DC PLC wiring diagram in Appendix A, install cloth Set Figure in Appendix B. Note. Does not include porcelain (or multiple sets) PLC DC filter capacitor structure.

DC porcelain (or multiple sets) structure PLC filter capacitor performance standards See IEC 60358-2. Its clauses include terms and definitions, abbreviations.

Found what you need?

Document preview — GB/T 32130-2015

National Standard of the People's Republic of China

ICS
31.060.70
Classification
K 42

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Introduction
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions, abbreviations
  • 3.1 Terms and definitions
  • 3.2 Abbreviations
  • 4 Conditions of Use
  • 4.1 normal conditions of use
  • 4.2 Non-normal conditions of use
  • 5 Quality requirements and testing
  • 5.1 Test requirements
  • 5.2 Test Category
  • 5.3 Visual inspection (routine test)
  • 5.4 Capacitance measurement (routine test)
  • 5.5 capacitor loss tangent (tandelta) Measurement (routine test)
  • 5.6 terminals voltage test (routine test)
  • 5.7 terminal and housing AC voltage test (routine test)
  • 5.8 Internal Pressure resistance measurement (routine test)
  • 5.9 Tightness test (routine test)
  • 5.10 Thermal stability test (type test)
  • 5.11 between terminal and housing AC voltage test (wet) (type test)
  • 5.12 between terminals and housing lightning impulse voltage test (type test)
  • 5.13 short circuit discharge test (type test)
  • 5.14 capacitance with temperature curve measurement (type test)
  • 5.15 polarity inversion test (type test)
  • 5.16 capacitor loss tangent (tandelta) versus temperature measurement (type test)
  • 5.17 casing and conducting rod stress test (type test)
  • 5.18 Visual inspection (acceptance test)
  • 5.19 between terminal and shell insulation resistance measurement (acceptance test)
  • 5.20 capacitance measurement (acceptance test)
  • 5.21 between terminal and housing AC voltage test (acceptance test)
  • 6 design and structural requirements
  • 6.1 capacitor bank
  • 6.2 capacitor gantry
  • 6.3 capacitor unit
  • 6.4 audible noise
  • 6.5 Mechanical Design
  • 6.6 Insulator
  • 6.7 terminal
  • 6.8 creepage distance
  • 6.9 Radio Interference (RIV) Design
  • 6.10 Welding
  • 6.11 Surface Treatment
  • 7 14 insulation level
  • 8 Overload
  • 9 Safety requirements
  • 9.1 discharge safety device 14 demands
  • 9.2 housing secure connection requirements
  • 9.3 Environmental security requirements
  • 9.4 Additional security requirements
  • 10 flag capacitor unit
  • 10.1 Nameplate
  • 10.2 15 Warning Signs
  • 11.1 specification or nameplate
  • 11.2 15 Warning Signs
  • 12 for installation and operation are
  • 12.1 Overview
  • 12.2 Selection of Rated Voltage
  • 12.3 stable
  • 12.4 Special conditions
  • Appendix A (informative) HVDC systems commonly filter DC PLC wiring diagram Example

1 Scope

This standard specifies the HVDC systems Terms and definitions PLC DC filter capacitor, conditions of use, design and construction, to

Basic requirements and test, quality and other aspects.

This standard applies to high-voltage direct current (HVDC) transmission system HVDC Converter Station side, installed in the indoor or outdoor DC PLC filter circuit

Container for filtering 30kHz ~ 500kHzPLC noise signal in the frequency range to prevent the carrier PLC converter valve noise generated in the frequency domain

Along the sound of a communication system noise interference. HVDC systems commonly filter DC PLC wiring diagram in Appendix A, install cloth

Set Figure in Appendix B.

Note. Does not include porcelain (or multiple sets) PLC DC filter capacitor structure. DC porcelain (or multiple sets) structure PLC filter capacitor performance standards

See IEC 60358-2.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 11024.1-2010 nominal voltage above 1000V ac power systems parallel capacitor - Part 1. General (IEC 60871-1.2005, MOD)

GB/T 16927.1-2011 high voltage test techniques - Part 1. General definitions and test requirements (IEC 60060-1.2010,

MOD)

GB/T 20993-2012 HVDC surge capacitor and a DC filter capacitor neutral bus

3 Terms and definitions, abbreviations

3.1 Terms and Definitions

GB/T 11024.1-2010 and GB/T 20993-2012 define the following terms and definitions apply to this document. To Party

It is repeated below lists the GB/T 11024.1-2010 and GB/T 20993-2012 some terms and definitions.

3.1.1 Capacitor element (element)

A dielectric and two electrodes separated by its members posed.

[GB/T 11024.1-2010, Definition 3.1]

3.1.2 Capacitor capacitor unit (unit) capacitorunit (unit)

By one or more capacitor elements assembled in the same housing and a lead terminal of the assembly.

[GB/T 11024.1-2010, the definition 3.2]

3.1.3 Series segment

All units are connected in parallel with a capacitor.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 20 pages — is available in the English PDF.

Similar standards

How to Download GB/T 32130-2015

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Instant delivery (0–9 sec)

    Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
20 pages
Instant delivery (0–9 sec)
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 32130-2015

$355.00