GB/T 30513-2014Technical requirements and testing method of tire blow-out monitoring and controlling system for passenger car (English PDF)
乘用车爆胎监测及控制系统技术要求和试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 30513-2014 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 13, 2013
Implementation date
June 1, 2014
Scope
GB/T 30513-2014 is the English-translated version of 乘用车爆胎监测及控制系统技术要求和试验方法.
GB/T 30513-2014 is the Chinese standard "Technical requirements and testing method of tire blow-out monitoring and controlling system for passenger car". Its scope clause reads: This standard specifies the passenger car tire monitoring and control system of terms and definitions, technical requirements, test methods.
This standard applies to systems equipped with ABS After installation vehicle tire monitoring and control system for M1 class vehicles. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 30513-2014
National Standard of the People's Republic of China
- ICS
- 43.040.40
- Classification
- T 24
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 2 Technical Requirements
- 5 Test Method
- Appendix A (normative) electrical load, mechanical load and climatic load performance requirements and test methods
1 Scope
This standard specifies the passenger car tire monitoring and control system of terms and definitions, technical requirements, test methods.
This standard applies to systems equipped with ABS After installation vehicle tire monitoring and control system for M1 class vehicles.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB 4208-2008 shell protection (IP code)
Flag GB 4094 automotive controls, indicators and telltales
GB/T 12534-1990 General car road test method
GB/T 17619-1998 vehicles to electromagnetic radiation immunity limits and methods of measurement of electrical and electronic components
GB/T 18655-2010 vehicles, boats and internal combustion engines - Radio disturbance characteristics for the protection of the onboard receiver limits and methods of measurement
GB/T 19951-2005 Road vehicles - Test method for generating an electrostatic discharge harassment
GB/T 21437.2-2008 Part 2 Electrical disturbances from conduction and coupling road vehicles cause. electrical transients along supply lines
Conduct
GB/T 26149-based automobile tire pressure monitoring tire pressure monitoring system module
GB/T 28046.1-2011 Environmental conditions and testing - Part 1 road vehicle electrical and electronic equipment. general provisions
GB/T 28046.2-2011 road vehicle electrical and electronic equipment - Environmental conditions and testing - Part 2. Electrical loads
GB/T 28046.3-2011 Environmental conditions and testing - Part 3 Road vehicles - electrical and electronic equipment. mechanical load
GB/T 28046.4-2011 road vehicle electrical and electronic equipment - Environmental conditions and testing - Part 4. Climatic loads
3 Terms and Definitions
GB/T 26149 and defined by the following terms and definitions apply to this document.
3.1 Puncture tireblow-out
The pneumatic tire pressure drop within 750ms to process the current ambient air pressure.
3.2 Vehicle tire monitoring and control system vehicletireblow-outmonitoringandcontrolingsystem; BMCS
Able to identify the vehicle tire puncture state, and the vehicle tire after traveling attitude control to ensure traffic safety systems.
3.3 Controller Module
For receiving the tire pressure monitoring module or receiver module to send a signal, and means to make the right judgments and reasonable process.
Note. Sometimes the receiver module and the controller module into one.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 30513-2014
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 30513-2014
$195.00