GB/T 30100-2013Test methods for building wallboard (English PDF)
建筑墙板试验方法
This is a limited preview
Buy now to download the full PDF (21 pages)
Need quotation for your management?
Get a formal quotation for GB/T 30100-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2013
Implementation date
September 1, 2014
Scope
GB/T 30100-2013 is the English-translated version of 建筑墙板试验方法.
GB/T 30100-2013 is the Chinese standard "Test methods for building wallboard".
Its scope clause reads: This standard specifies the building panel appearance quality, dimension deviation, surface density, moisture content, water absorption, relative water content, compressive strength, softened Coefficient, frost resistance, carbonation coefficient, bending strength, bending load, impact resistance, hanging strength, anti-pull, drying shrinkage, efflorescence, anti-reversion halogen resistance, Permeability and water impermeability test methods.
This standard applies to industrial and civil use building panel. Its clauses include terms and definitions; test environment and test conditions; appearance quality and size deviation.
Found what you need?
Document preview — GB/T 30100-2013
National Standard of the People's Republic of China
- ICS
- 91.100.01
- Classification
- Q 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 test environment and test conditions
- 5 appearance quality and size deviation
- 7 moisture content, relative water content and water absorption
- 8 compressive strength, softening coefficient, frost resistance, carbonation factor of
- 9 flexural strength
- 11 12 Impact Resistance
- 12 hanging power
- 13 17 Pulling
- 14 drying shrinkage
- 15 pan-cream, anti-reversion halo of
- 16 anti-permeability, water impermeability
- 17 22 Test Report
1 Scope
This standard specifies the building panel appearance quality, dimension deviation, surface density, moisture content, water absorption, relative water content, compressive strength, softened
Coefficient, frost resistance, carbonation coefficient, bending strength, bending load, impact resistance, hanging strength, anti-pull, drying shrinkage, efflorescence, anti-reversion halogen resistance,
Permeability and water impermeability test methods.
This standard applies to industrial and civil use building panel.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 17671 cement mortar strength test method (ISO method)
GB/T 18968 wall material terms
GB/T 25183 wall bricks compressive strength test grout material
3 Terms and Definitions
Terms and definitions GB/T 18968 apply to this document defined.
4 test environment and test conditions
Unless otherwise stated, tests are conducted under normal temperature and humidity environmental conditions, all subjects wallboard products should reach curing period prescribed.
5 appearance quality and size deviation
Measuring 5.1
5.1.1 Steel ruler
accuracy 0.5mm.
5.1.2 steel tape measure
accuracy 1mm.
5.1.3 vernier caliper
accuracy 0.02mm.
5.1.4 feeler
accuracy 0.01mm.
5.1.5 on foot
Range 2m.
5.1.6 reading microscope
the accuracy of 0.01mm.
5.1.7
inside and outside calipers.
5.2 Appearance quality inspection
On the board under test, about 0.5m horizon visually whether the exposed reinforcing fibers through the cracks, efflorescence; steel ruler to measure the crack length board,
Honeycomb holes, missing edge off angle data readings accurate to 1mm; measuring the crack width with a reading microscope, accurate readings to 0.1mm, and record
Number.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 21 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 23450-2024Heat preservation panels for partition wall used in buildings
- JG/T 574-2019Fiber-reinforced cladding wood matrix composite panels for building
- GB/T 36140-2018Technical requirements for assembled insulation combination wall composite by glass fiber reinforced inorganic materials
- JG/T 506-2016Tailings Crystallite Foaming Sheet and Masonry Block
Similar standards
How to Download GB/T 30100-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 30100-2013
$355.00