GB/T 30040.7-2013Leak detection systems - Part 7: General requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jacket (English PDF)
双层罐渗漏检测系统 第7部分：双层间隙、防渗漏衬里及防渗漏外套的一般要求和试验方法
This is a limited preview
Buy now to download the full PDF (21 pages)
Need quotation for your management?
Get a formal quotation for GB/T 30040.7-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 17, 2013
Implementation date
September 1, 2014
Scope
GB/T 30040.7-2013 is the English-translated version of 双层罐渗漏检测系统 第7部分：双层间隙、防渗漏衬里及防渗漏外套的一般要求和试验方法.
GB/T 30040.7-2013 is the Chinese standard "Leak detection systems - Part 7: General requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jacket".
Its scope clause reads: GB/T 30040 provisions of this part of the double-gap, anti-leakage and anti-seepage lining of the jacket material, double gap type test, Leak-proof lining and the general requirements and test methods leakproof jacket.
This section applies to a double gap double tank leak detection systems, anti-leakage and anti-leak liner jacket.
Found what you need?
Document preview — GB/T 30040.7-2013
National Standard of the People's Republic of China
- ICS
- 29.260.20
- Classification
- G 93
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 material
- 5 double gap type test
- 6 leakproof liner
- 7 leakproof jacket
- 2 double gap structure rationality test
- 6 in a laboratory test apparatus 10 of FIG injected water
- 7 14 impact test apparatus in FIG.
- 9 schematic test tank wall
1 Scope
GB/T 30040 provisions of this part of the double-gap, anti-leakage and anti-seepage lining of the jacket material, double gap type test,
Leak-proof lining and the general requirements and test methods leakproof jacket.
This section applies to a double gap double tank leak detection systems, anti-leakage and anti-leak liner jacket.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
Determination of GB/T 1034 plastic water absorption
1040.1 Plastics Determination of tensile properties GB/T Part 1. General
Test conditions for films and sheets. plastic 1040.3 Determination of tensile properties GB/T Part 3
Measuring performance GB/T 1041 plastic compression
GB /Plastics - Determination of Charpy impact properties of T 1043.1 - Part 1. Non-instrumented impact test
Determination of GB/T 1634.1 plastic deflection temperature under load - Part 1. General test method
Determination of GB/T 1634.2 plastic deflection temperature under load - Part 2. Plastics, ebonite and long-fiber-reinforced composite materials
Determination of GB/T 1634.3 plastic deflection temperature under load - Part 3. High - strength thermosetting laminates
GB/T 8923.1 steel substrates before application of paints and Visual assessment of surface cleanliness - Part 1. uncoated steel
Rust grades and preparation grades of steel surfaces and surfaces after overall removal of previous coatings
Determination of GB/T 9341 plastic bending performance
Determination of GB/T 11547 plastic resistant liquid chemical reagents -
Curve analysis GB/T 12833 Rubber and plastic tear strength and adhesion strength measurement of a multimodal
Motor gasoline GB 17930
GB/T 30040.1-2013 double-tank leak detection systems - Part 1. General
GB/T 30040.2-2013 double-tank leak detection system, Part 2. Pressure and vacuum systems
ISO 554 regulation and/or test standard specification atmosphere
ISO 2528 sheet water vapor transmission rate - Gravimetric (disc) analysis
ISO 4599 Plastics - Determination of resistance to environmental stress cracking deformation plate method
Determination ENISO 179-2 plastic Charpy impact properties - Part 2. Instrumented impact test
Peeling resistance was measured EN431 resilient floor coverings
Flexible sheets for waterproofing EN495-5 low folded Determination - Part 5. Plastic and rubber roof waterproofing layer
EN976-2 glass fiber reinforced plastic underground storage tanks non-pressure storage of liquid petroleum fuels horizontal cylindrical or cylindrical receptacle
Cans - Part 2. Single-wall tank transport, storage, handling and installation
Flexible sheets for waterproofing EN1107-2 Determination of dimensional stability - Part 2. Plastic and rubber roof waterproofing layer […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 21 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 30040.7-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 30040.1-2013 — Leak detection systems—Part 1: General principles
GB/T 30040.2-2013 — Leak detection systems—Part 2: Pressure and vacuum systems
GB/T 30040.3-2013 — Leak detection systems - Part 3: Liquid systems for tanks
Secure payment via Stripe
Payments accepted
GB/T 30040.7-2013
$375.00