GB/T 29190-2012Measurement methods of drift rate of scanning probe microscope (English PDF)
扫描探针显微镜漂移速率测量方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 29190-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2012
Implementation date
June 1, 2013
Scope
GB/T 29190-2012 is the English-translated version of 扫描探针显微镜漂移速率测量方法.
GB/T 29190-2012 is the Chinese standard "Measurement methods of drift rate of scanning probe microscope".
Its scope clause reads: This standard specifies the terms and definitions SPM drift rate, abbreviations, measurement procedures, performance parameter specifications, and SPM-based scanning The drift rate of the image of the basic methods of measurement.
This standard applies to 0.01nm/s to drift rate 10nm/s measurements. This standard does not apply to wander measurement image correction. Its clauses include terms and definitions, abbreviations.
Found what you need?
Document preview — GB/T 29190-2012
National Standard of the People's Republic of China
- ICS
- 17.180.99
- Classification
- A 60
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions, abbreviations
- 4 Measurement
- 5 Requirement
- 5.1 Instrument Requirements
- 5.2 Environmental Requirements
- 6 measuring step
- 7 3 Measurement Report
- Appendix A (normative) image correlation analysis
- Appendix B (normative) Characteristic Point Method
- Annex C (normative) Non-periodic grating method
- Annex D (informative) method atomic grating
- Appendix E (normative) Measurement Method Comparison
- References
1 Scope
This standard specifies the terms and definitions SPM drift rate, abbreviations, measurement procedures, performance parameter specifications, and SPM-based scanning
The drift rate of the image of the basic methods of measurement.
This standard applies to 0.01nm/s to drift rate 10nm/s measurements. This standard does not apply to wander measurement image correction.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 15000.3 standard for the work of (3) the general principles of the standard sample value and statistical methods;
JJF1001 common measurement terms and definitions;
JJF1059 Evaluation and Expression of Uncertainty in Measurement (ISO GUM.1995, IDT);
ISO 18115 Surface chemical analysis noun, Part 2. scanning probe microscopy applicable term (Surfacechemical analysis-Vocabulary-Part 2. Termsusedinscanning-probemicroscopy).
3 Terms and definitions, abbreviations
GB/T 20000.1 and the following definition of terms and definitions, abbreviations apply to this document.
3.1 Terms and Definitions
3.1.1 Drift
SPM instrument probe relative to the deviation of the actual position and the set position of the sample.
Note. All parameter settings are likely to drift, such as x, y, z displacement direction of the laser spot position on the cantilever, the optical near-field scanning optical microscope
Source strength. This standard, the drift is defined as the x, y and z directions, the probe relative to the sample is set to change the location.
3.1.2 Drift rate
Drift with the time interval than a certain time interval.
Note 1. The time interval is usually chosen as the adjacent images obtained by scanning continuously between.
Note 2. The drift rate can be given as a drift rate x, y and z directions, or corresponding synthetic vector magnitude.
3.1.3 Set time settlingtime
From the point of the selected area of the sample to be measured or the sample begins to wander measurement interval.
NOTE. Set the time usually selected for 5min ~ 60min.
3.2 Acronyms
The following abbreviations apply to this document.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 29190-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 29190-2012
$255.00