Valid

GB/T 29147-2012Methodology of the calculation of residuary heat resource during manufacturing of prepainted and galvanized steel (English PDF)

钢铁生产余热资源计算方法 涂镀

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 29147-2012 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 31, 2012

Implementation date

October 1, 2013

Scope

GB/T 29147-2012 is the English-translated version of 钢铁生产余热资源计算方法 涂镀.

GB/T 29147-2012 gives a method for calculating the residuary heat resource in the manufacturing of prepainted and galvanized steel.

Clause 1 says the standard specifies the terms and definitions of waste heat and the calculation of waste heat resources for the hot dip and prepainting production processes, that it applies to those processes, and that the continuous annealing process may be carried out by reference to it.

Clause 2 cites YB/T 4210 and YB/T 4211. Clause 3 holds a single definition, for the flue gas, vapour and similar discharges of the hot dip furnace, the coating curing oven, the incinerator and other heating systems, which the draft names coated exhaust, with prepainted and galvanized steel gas as its English form, and shortens to gas.

Clause 4, Calculation, recommends 180 degrees Celsius as the physical limit temperature for using the waste heat of the exhaust, then gives the total waste heat resource as the sum of the physical and the chemical waste heat resources of the exhaust, the physical part as the sum of the dry gas and the water vapour contributions, and a third formula for the dry gas part, all of them in kilojoules per year, with the exhaust gas volume in that formula either measured or calculated.

The draft breaks off inside the symbol list of 4.3.1, so nothing after it is shown. The standard was proposed by China Iron and Steel Association and is administered jointly by SAC/TC20 and SAC/TC183, under ICS 77.010 and Chinese classification H46. It was issued on 31 December 2012 and has applied since 1 October 2013.

Found what you need?

Document preview — GB/T 29147-2012

National Standard of the People's Republic of China

ICS
77.010
Classification
H 46

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 Calculation

Foreword

This standard was drafted in accordance with GB/T 1.1-2009 given rules. The standard proposed by China Iron and Steel Association.

1 Scope

This standard specifies the production of hot dip steel, pre-painted process terms and definitions of waste heat and waste heat resource calculation.

This standard applies to the production of hot dip steel, pre-painted and other processes. Continuous annealing step can be implemented by reference.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.

YB/T 4210 color coated sheet production line incinerator furnaces and thermal balance determination and calculation of solidification

YB/T 4211 hot-dip galvanizing line furnace heat balance determination and calculation

3 Terms and Definitions

The following terms and definitions apply to this document.

3.1 Coated exhaust prepainted and galvanized steel gas

Discharging hot dip furnace, coating curing ovens, incinerators, and other heating systems fumes, vapors and the like. Hereinafter referred to as gas.

4 Calculation

4.1 Recommended exhaust waste heat utilization of physical limit temperature of 180 °C.

4.2 exhaust heat contained in the sum of the amount of resources for some physical quantity of waste heat and chemical waste heat resources, see formula (1). Qy = Qw Qh (1) Where.

Qy --- the amount of waste heat resources in units of kilojoules per year (kJ/a);

In the exhaust heat Qw --- physical resources, units of kilojoules per year (kJ/a);

Qh --- chemical heat of exhaust gas resources in units of kilojoules per year (kJ/a).

4.3 When the actual calculation of existing equipment, exhaust gas heat of physical resources in which dry gas physical heat in the exhaust gas and water resources The sum of the sub-physical waste heat resources, see formula (2). Qw = Qg Qs (2) Where.

Qg --- Dry heat exhaust physical resources, in units of kilojoules per year (kJ/a);

Qs --- exhaust gas heat water physical resources, units of kilojoules per year (kJ/a).

4.3.1 Dry heat exhaust physical resources are calculated in the formula (3).

Qg = V (1-0.00124s) . (cf . tf-cx . tx) (3) Where.

V --- amount of exhaust gas discharged in units of cubic meters per year method (m3/a), may be the actual measurements and theoretical calculations, theoretical calculation

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 29147-2012

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 29147-2012

$85.00