GB/T 2856.2-2008Holders for ball-bearing die sets for stamping dies - Part 2: Die holders for die sets (English PDF)
冲模滚动导向模座 第2部分：下模座
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 2856.2-2008 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
April 10, 2008
Implementation date
October 1, 2008
Scope
GB/T 2856.2-2008 is the English-translated version of 冲模滚动导向模座 第2部分：下模座.
GB/T 2856.2-2008 is the Chinese standard "Holders for ball-bearing die sets for stamping dies - Part 2: Die holders for die sets". Its scope clause reads: This section provides the die rolling guide structure, sizes and mark the lower die holder.
This section applies to the die rolling guide with the lower die. Its clauses include dimensions.
Found what you need?
Document preview — GB/T 2856.2-2008
National Standard of the People's Republic of China
- ICS
- 25.120.30
- Classification
- J 46
- Replacing
- GB/T 2856.6-1990
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Dimensions
- 3.1 diagonal pillar mold base
1 Scope
This section provides the die rolling guide structure, sizes and mark the lower die holder.
This section applies to the die rolling guide with the lower die.
2 Normative references
The following documents contain provisions which, through reference to GB/T 2856 to the present, constitute provisions of this section. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
JB/T 8070 die mold parts and technical conditions
3 Dimensions
3.1 diagonal pillar mold base
The structure of the mold base and the lower corner pillar dimensions shown in Figure 1, Table 1.
Note the surface roughness is not a non-machined surface.
Figure 1 diagonal pillar mold base […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 2856.2
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 2856.2-2008 | Holders for ball-bearing die sets for stamping dies - Part 2: Die holders for die sets | current edition | Current |
| GB/T 2856.6-1990 | Holders for ball-bearing die sets for stamping dies - Part 2: Die holders for die sets | previous edition | Superseded |
This page sells the current edition, GB/T 2856.2-2008. Earlier editions are listed for reference only.
How to Download GB/T 2856.2-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 2856.1-2008 — Holders for ball-bearing die sets for stamping dies - Part 1: Punch holders for die sets
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
Secure payment via Stripe
Payments accepted
GB/T 2856.2-2008
$115.00