GB/T 26066-2010practice for shallow etch pit detection on silicon (English PDF)
硅晶片上浅腐蚀坑检测的测试方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 26066-2010 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
January 10, 2011
Implementation date
October 1, 2011
Scope
GB/T 26066-2010 is the English-translated version of 硅晶片上浅腐蚀坑检测的测试方法.
GB/T 26066-2010 is the Chinese practice for revealing shallow etch pits on silicon.
It specifies the preferential etching test by which the pits caused by contamination are shown on the surface of a polished wafer after thermal oxidation and chemical treatment, with the reagents, the apparatus, the specimen, the procedure, the examination of the surface and the report.
It applies to polished and epitaxial wafers of (111) or (100) orientation, p-type or n-type, with a resistivity above 0.001 ohm·cm. Wafer producers and the process control laboratories of a fab use it. Issued on 10 January 2011, it has applied since 1 October 2011.
Found what you need?
Document preview — GB/T 26066-2010
National Standard of the People's Republic of China
- ICS
- 29.045
- Classification
- H 80
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Method summary
- 5 Significance and Use
- 6 Disturbances
- 7 Equipment
Foreword
The standard equipment by the National Standardization Technical Committee and the Technical Committee material of the semiconductor material (SAC/TC203/SC2) centralized.
1 Scope
This standard specifies thermal oxidation and chemical preferential etching techniques or polished wafer inspection surface due to contamination caused by shallow pit corrosion inspection Measuring method.
This standard is applicable to the detection of < 111> or < 100> p-type or n-type polished or epitaxial wafers, resistivity greater than 0.001ohm · cm.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 14264 semiconductor material terms
3 Terms and Definitions
Terms and definitions GB/T 14264 apply to this document defined.
4 Method summary
Some defects polished or epitaxial wafers after thermal oxidation and preferential etching by microscopic observation after showing shallow corrosion pits, and a chart Identifying and documenting the extent of corrosion pits.
5 Significance and Use
5.1 High-density corrosion pits ( > 10^4/cm2) showed that metal contamination on a silicon wafer, semiconductor device fabrication process is harmful.
Objective 5.2 test method is used for incoming inspection and process control.
6 Disturbances
6.1 corrosion and corrosion before the bubble generated in the process of cleaning the surface of undue influence observations.
6.2 insufficient amount of etching solution will affect the observed effect.
6.3 Preferential etching process to prevent serious contamination of silicon p-type silicon
(< 0.2ohm · cm) to form a shallow corrosion pits or blur it.
6.4 oxidizing environment contamination will seriously increase the density of shallow corrosion pits.
7 Equipment
7.1 high-intensity narrow beam of light. illumination more than 16klx (1500fc) tungsten filament from the light source position of the beam diameter 20mm ~ 100mm 40mm.
7.2 hydrofluoric acid protective equipment. fluorine plastic, polyethylene or polypropylene beaker, graduated cylinder, tweezers, goggles, aprons, gloves and protective sleeves.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
Similar standards
How to Download GB/T 26066-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 14264-1993 — Semiconductor materials-Terms and definitions
GB/T 14264-2009 — Semiconductor materials - Terms and definitions
GB/T 14264-2024 — Terminology of semiconductor materials
GB/T 26066-2010
$105.00