Valid

GB/T 25781-20101-Naphthyamine (English PDF)

1-萘胺

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 25781-2010 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 23, 2010

Implementation date

October 1, 2011

Scope

GB/T 25781-2010 is the English-translated version of 1-萘胺.

GB/T 25781-2010 is the Chinese standard "1-Naphthyamine".

Its scope clause reads: This standard specifies the requirements, sampling, test methods, inspection rules, and marking, labeling, packaging, transportation, storage and safety of 1-naphthylamine: Safety Data Sheet: This standard applies to the product quality control of 1-naphthylamine: Structural formula:.

Its clauses include requirements; samples; test methods; inspection rules; marking, labeling, packaging, transport and storage; safety and safety technical manual.

Found what you need?

Document preview — GB/T 25781-2010

National Standard of the People's Republic of China

ICS
71.100.01
Classification
G 56

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Requirements
  • 4 samples
  • 5 Test methods
  • 6 Inspection Rules
  • 7 Marking, Labeling, Packaging, Transport and Storage
  • 8 Safety and safety technical manual

1 Scope

This standard specifies the requirements, sampling, test methods, inspection rules, and marking, labeling, packaging, transportation, storage and safety of 1-naphthylamine:

Safety Data Sheet:

This standard applies to the product quality control of 1-naphthylamine:

Structural formula:

2 Normative references

The clauses in the following documents become clauses of this standard through reference in this standard: For dated references, all subsequent

The amendments (excluding errata content) or revisions do not apply to this standard, however, the parties to the agreement based on this standard are encouraged to study

Is the latest version of these files available: For undated references, the latest edition applies to this standard:

GB 190 Dangerous Goods Packaging Marks

GB/T 191 Graphical Marks for Packaging, Storage and Transportation (GB/T 191-2008, ISO 780:1997, MOD)

Preparation of GB/T 601 Standard Titration Solutions for Chemical Reagents

Preparation of preparations and products used in GB/T 603 chemical reagent test methods (GB/T 603-2002, neqISO 6353-1:

1982)

GB/T 2385-2007 General method for determination of crystallization point of dye intermediates

GB/T 6678-2003 General rules for sampling of chemical products

GB/T 6682 Analysis Laboratory Water Specifications and Test Methods (GB/T 6682-2008, ISO 3696:1987, MOD)

GB/T 8170-2008 Numerical Rounding Rules and Representation and Judgment of Limit Values

GB/T 9722 General Rules for Gas Chromatography of Chemical Reagents

GB/T 12268-2005 Dangerous Goods List

GB 12463 General Specifications for Transport Packaging of Dangerous Goods

GB 15258 Regulations for the preparation of chemical safety labels

GB 15603 General Rules for the Storage of Commonly Used Chemical Dangerous Goods

GB 16483 Regulations for the preparation of chemical safety data sheets (GB 16483-2000, eqvISO 11014-1:1994)

3 Requirements

The quality of 1-naphthylamine should meet the requirements of Table 1:

4 samples

Sampling is taken in batches, and the production plant takes uniform products as a batch: The number of samples in each batch shall comply with the regulations in 7:6 of GB/T 6678-2003

Certainly: The packaging of the samples to be sampled must be intact, and foreign impurities should not fall into the product during sampling: When sampling, use a probe to take three steps including upper, middle and lower

For some samples, the total amount of samples sampled shall not be less than 500g: After fully mixing the collected samples, divide them into two clean, dry and well-sealed containers:

In a good light-proof container, stick a label on it: Note: product name, batch number, manufacturer name, sampling date, location: one for inspection, one saved for future reference:

5 Test methods

WARNING - Persons using this standard should have practical experience in laboratory work: This standard does not address all safety issues: use

It is the responsibility of the operator to take appropriate safety and health measures and to ensure compliance with the conditions stipulated by the relevant national regulations:

5:1 General provisions

Unless otherwise specified, the reagents and water used in this standard, unless other requirements are specified, refer to analytical reagents and those specified in GB/T 6682:

Specified tertiary water: The standard solutions, preparations and products required in the test, unless other regulations are specified, shall be in accordance with GB/T 601, GB/T 603

Provisions for preparation and calibration: The judgment of the test results shall be carried out according to the rounding value comparison method in 4:3:3 of GB/T 8170-2008:

5:2 Evaluation of appearance

Visual assessment was performed under natural light:

5:3 Determination of crystallization point of dry product

Take about 50g of sample and 10g of 0:5nm (5Å) molecular sieve in a 125mL wide-mouth bottle, close the stopper tightly, heat the sample to melt, and remove it:

Water for 15min (shake the sample bottle several times during the melting process), and the rest shall be carried out according to the provisions of GB/T 2385-2007:

5:4 Determination of 1-naphthylamine content (total amino group value)

5:4:1 Reagents and solutions a) Hydrochloric acid solution: the volume ratio of hydrochloric acid to water is 1:1;

b) Potassium bromide solution: 100g/L;

c) Sodium nitrite standard titration solution: [c(NaNO2)=0:1mol/L], starch-potassium iodide test paper is used for end point determination;

d) Starch-potassium iodide test paper:

5:4:2 Measurement steps

Weigh about 0:5g (accurate to 0:0002g) of 1-naphthylamine sample into a 500mL beaker, add 100mL of 90°C hot water, and stir under stirring:

Slowly add 10 mL of hydrochloric acid solution, after the sample is completely dissolved, add 30 mL of hydrochloric acid solution, add water to a total volume of 300 mL, and cool to

0°C~5°C: Add 10 mL of potassium bromide solution, then insert the tip of the burette into the solution, and under constant stirring, drop standard sodium nitrite with sodium nitrite:

The titration solution was titrated: During the titration process, the reaction temperature was kept at 0°C to 5°C:

Titrate until the starch-potassium iodide test paper presents a slight blue circle, and keeps it unchanged for 5min as the end point: Under the same conditions, make a blank test:

5:4:3 Result calculation

The content of 1-naphthylamine (total amino group value) is calculated in w1, the value is expressed in %, and calculated according to formula (1):

Calculation results are expressed to two decimal places:

5:4:4 Tolerance

The difference between the results of the two parallel determinations should not be greater than 0:3% (mass fraction), and the arithmetic mean is taken as the determination result:

5:5 Determination of 2-naphthylamine content (HPLC)

5:5:1 Method summary

The content of 2-naphthylamine was calculated by reversed-phase liquid chromatography and external standard method:

5:5:2 Instruments a) Liquid chromatograph: infusion pump---flow range (0:1~5:0)mL/min, within this range its flow stability is ±1%;

Detector---multi-wavelength UV spectroscopic detector or UV spectroscopic detector with equivalent performance;

b) Chromatographic column: a stainless steel column with a length of 150 mm and an inner diameter of 4:6 mm, the stationary phase is ODSC18, and the particle size is 5 µm;

c) Data processor: chromatography workstation or integrator;

d) ultrasonic generator;

e) Micro syringe: 25 µL;

f) Microbalance: Sensitive amount is 0:01mg:

5:5:3 Reagents and solutions a) Methanol: chromatographically pure;

b) Sodium dihydrogen phosphate aqueous solution: 0:6g/L sodium dihydrogen phosphate, adjust pH~4 with phosphoric acid;

c) The mass fraction of 2-naphthylamine standard product is >=98:0%;

d) Water: filtered through 0:45µm water membrane:

5:5:4 Chromatographic analysis conditions a) mobile phase: the volume ratio of methanol and sodium dihydrogen phosphate aqueous solution is 50:50;

b) Wavelength: 235nm;

c) Flow rate: 1:0mL/min;

d) Injection volume: 5µL:

The optimal separation conditions can be selected according to different instrument conditions:

5:5:5 Determination steps

5:5:5:1 Preparation of standard solution

Weigh 30 mg of 2-naphthylamine standard sample (accurate to 0:01 mg) in a 50 mL volumetric flask, dissolve it with methanol and make up to volume, and place it in an ultrasonic wave

The generator is fully dissolved, take out and shake well for use, it is standard solution A:

Pipette 2mL of standard solution A into a 50mL volumetric flask, dissolve it with methanol and set the volume, place it in an ultrasonic generator to fully dissolve it, and take it out:

Shake well for use as standard solution B:

Draw standard solution B according to Table 2 and prepare a series of standard solutions with different concentrations:

5:5:5:2 Preparation of sample solution

Weigh 0:15g of 1-naphthylamine sample (accurate to 0:0002g) in a 50mL volumetric flask, dissolve and dilute to the mark with methanol, mix evenly:

5:5:5:3 Determination

After the instrument runs stably, use a micro-syringe to draw the appropriate standard solution and sample solution and inject them into the injection valve respectively:

After the elution of each component is completed (see chromatogram 1), the results are processed:

5:5:6 Result calculation

The content of 2-naphthylamine is calculated in mass fraction w2, the value is expressed in %, and calculated according to formula (2):

w2=

A1m2w

A2m1 (2) where:

A1---the peak area value of 2-naphthylamine in the sample solution;

m2---the value of the mass of 2-naphthylamine in the standard solution, in grams (g);

w---the value of 2-naphthylamine content in the standard solution, in mass fraction (%);

A2---the peak area value of 2-naphthylamine in the standard solution;

m1---the value of the sample mass, in grams (g):

Calculation results are expressed to two decimal places:

5:5:7 Tolerance

The difference between the two parallel determination results should not be greater than 0:03% (mass fraction), and the arithmetic mean is taken as the determination result:

5:5:8 Chromatogram

The chromatogram is shown in Figure 1:

6 Inspection Rules

6:1 Inspection classification

All items specified in Table 1 of Chapter 3 of this standard are factory inspection items:

6:2 Factory inspection

1-Naphthylamine should be inspected and qualified by the quality inspection department of the manufacturer, and can only leave the factory after the certificate of conformity is attached: The manufacturer shall ensure that all

1-Naphthylamine all meet the requirements of this standard:

6:3 Retest

If one of the indicators in the inspection results does not meet the requirements of this standard, it should be re-sampled from twice the amount of packaging for inspection and re-examined:

Even if only one index does not meet the requirements of this standard as a result of the inspection, the whole batch of products is unqualified:

7 Marking, Labeling, Packaging, Transport and Storage

7:1 Signs and labels

Each package of 1-naphthylamine should be coated with firm and clear toxic signs and

Relevant safety storage and transportation signs, and indicate: product name specification, registered trademark, product production license number and logo, net content, manufacturer name

Name, factory address, standard number, batch number, production date: The batch number and production date can also be printed on the label, together with the certificate of product quality inspection:

together with the outside of the plastic bag in the packaging bucket: And should comply with GB 15258 chemical safety label preparation regulations:

7:2 Packaging

1-Naphthylamine is packaged in woven bags or paper-plastic composite bags lined with black plastic bags, with a net weight of 25kg per bag, other packaging can be negotiated with the user

Certainly: Product packaging should comply with GB 12463 and relevant regulations on packaging of hazardous chemicals:

7:3 Transport

Storage and transportation should comply with the relevant provisions of GB/T 191, and should be handled with care during transportation to prevent sunlight, collision and rain:

7:4 Storage

1-Naphthylamine is toxic and can burn in the presence of open flames: It should be stored away from sources of ignition and fire, and placed in a cool and dry place: Product storage should be in accordance with

GB 15603 and relevant regulations on the storage of hazardous chemicals:

8 Safety and safety technical manual

8:1 Safety

According to GB 12268-2005, 1-naphthylamine belongs to class 6:1 toxic substances, dangerous goods number (UN: 2077; CN: 61830): flammable, subject to

Thermal decomposition produces toxic gases: Mainly by the respiratory tract, gastrointestinal tract and skin into the human body and cause poisoning: Bladder swelling in people who have been exposed for a long time tumor: Rat caliber LD50: 779mg/kg: In case of accident, seek medical attention in time: When using and handling, you should wear labor protection equipment:

be careful:

8:2 Safety Data Sheet

According to the preparation of GB 16483 chemical safety technical instructions, 1-naphthylamine should provide detailed safety technical instructions when leaving the factory: safety technology

The instruction manual should include the following:

a) provide information on the hazard of the product;

b) safe use method;

c) Transportation and storage requirements;

d) protective measures;

e) Emergency treatment measures, etc:

GB/T 21892-2015 | GB/T 15336-2013 | GB/T 25787-2010 | GB/T 25789-2023 | GB/T 25786-2016 | GB/T 25780-2010 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 25781-2010

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 25781-2010

$125.00