GB/T 25495-2010Test methods for metal releasing characteristics of getters (English PDF)
吸气剂金属释放特性测试方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 25495-2010 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 1, 2010
Implementation date
May 1, 2011
Scope
GB/T 25495-2010 is the English-translated version of 吸气剂金属释放特性测试方法.
GB/T 25495-2010 is the Chinese standard "Test methods for metal releasing characteristics of getters".
Its scope clause reads: This standard specifies the characteristics of getter metal release test methods, such as the total amount of mercury releasing mercury releasing getter, the standard amount of mercury release, mercury release characteristic curve Test Method for wire and thermal stability, barium evaporable getter method was tested a barium amount of nitrogen-doped barium getter film distribution test methods.
This standard applies to devices with a vacuum getter. Its clauses include terms.
Found what you need?
Document preview — GB/T 25495-2010
National Standard of the People's Republic of China
- ICS
- 31.030
- Classification
- L 90
- Replacing
- GB 9506.6-1988
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Terms
- 4.1 Principle
- 4.2 Test equipment and conditions
1 Scope
This standard specifies the characteristics of getter metal release test methods, such as the total amount of mercury releasing mercury releasing getter, the standard amount of mercury release, mercury release characteristic curve
Test Method for wire and thermal stability, barium evaporable getter method was tested a barium amount of nitrogen-doped barium getter film distribution test methods.
This standard applies to devices with a vacuum getter.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent
Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 4314 getter term
GB/T 25494-2010 getter composition analysis test methods
3 Terms
GB/T 4314 as determined by the terms and definitions apply to this standard.
Test Method 4 release of metal
4.1 Principle
Getter metal emission tests, such as the total amount of mercury releasing mercury releasing getter, the standard interpretation of the amount of mercury, barium evaporable getter yield of barium, etc., were collected
Determination of the amount of metal released by "poor weight method."
4.2 Test equipment and conditions
When evaporable getter tested, recommended the sample chamber and the high frequency induction coil size are shown in Table 1. The specimen shall be in cylindrical specimens
Rooms, and high-frequency induction coil center. Typically, the sample is placed on top of the sample chamber can be directed towards the evapotranspiration horizontal position, using coaxial
Evapotranspiration. For antenna type pallet color picture tube getter, for the ET direction towards the opposite glass wall, at least with the sample specimen support frame
Chamber axis angle of 30 °; the sample in order to prevent displacement occurs during evapotranspiration, evapotranspiration should be tangential. see picture 1.
GB/T 28159-2025 | GB/T 37406-2019 | GB/T 29848-2018 | GB/T 25497-2010 | GB/T 25496-2010 | GB/T 25494-2010 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 25495
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 25495-2010 | Test methods for metal releasing characteristics of getters | current edition | Current |
| GB 9506.6-1988 | Test methods for metal releasing characteristics of getters | previous edition | Superseded |
This page sells the current edition, GB/T 25495-2010. Earlier editions are listed for reference only.
How to Download GB/T 25495-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 25495-2010
$165.00