GB/T 24652-2009Steering rocking arm of wheeled tractors - Specifications (English PDF)
轮式拖拉机转向摇臂 技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 24652-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
November 15, 2009
Implementation date
May 1, 2010
Scope
GB/T 24652-2009 is the English-translated version of 轮式拖拉机转向摇臂 技术条件.
GB/T 24652-2009 is the Chinese standard "Steering rocking arm of wheeled tractors - Specifications". Its scope clause reads: This standard specifies wheeled tractor steering arm (including the pitman arm, steering knuckle arm, tie rod arm) requirements, test methods, inspection regulations Then, signs, packaging, transport and storage.
This standard applies to wheeled tractor steering arm (hereinafter referred to as the steering arm). Its clauses include requirements.
Found what you need?
Document preview — GB/T 24652-2009
National Standard of the People's Republic of China
- ICS
- 65.060.10
- Classification
- T 65
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Requirements
- 3.1 General requirements
1 Scope
This standard specifies wheeled tractor steering arm (including the pitman arm, steering knuckle arm, tie rod arm) requirements, test methods, inspection regulations
Then, signs, packaging, transport and storage.
This standard applies to wheeled tractor steering arm (hereinafter referred to as the steering arm).
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent
Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 157 Geometrical product specifications (GPS) conical tapers and taper angle Series (GB/T 157-2001, eqvISO
1119.1998)
GB/T 231.1 metallic materials Brinell hardness test - Part 1. Test method (GB/T 231.1-2009, ISO 6506-1.
2005, MOD)
GB/T 1031 Geometrical product specifications (GPS) Surface texture Profile method Surface roughness parameters and their values
Sectional dimensions GB/T 1095 flat key keyway
GB/T 1096 Ordinary flat key (GB/T 1096-2003, ASMEB18.25.1M.1996, NEQ)
GB/T 1098 Woodruff key keyway cross-sectional dimensions (GB/T 1098-2003, ASMEB18.25.2M.1996, NEQ)
GB/T 1184-1996 shape and position tolerances without individual tolerance value (eqvISO 2768-2. 1989)
Sectional dimensions GB/T 1563 Taper keys keyways
GB/T 1800.2-2009 Geometrical product specifications (GPS) limits and fits - Part 2. Standard tolerance grades and holes and shafts
Limit deviations (ISO 286-2. 1988, ISO Systemoflimitsandfits-Part 2. Tablesofstandardtolerance gradesandlimitdeviationsforholesandshafts, MOD)
GB/T 2828.1 Sampling procedures for inspection - Part 1. by acceptance quality limit (AQL) retrieval batch inspection sampling plan (GB/T 2828.1-2003, ISO 2859-1.1999, IDT)
GB/T 3478.1 Straight cylindrical involute splines (Metric module, side fit) - Part 1. General (GB/T 3478.1-
2008, ISO 4156-1.2005, MOD)
GB/T 12362 pieces of steel forging tolerances and machining allowances
JB/T 5673 agricultural and forestry tractors and machinery paint general technical conditions
System test method JB/T 7279 wheeled tractor mechanical steering
3 Requirements
3.1 General requirements
3.1.1
The steering arm shall conform to the requirements of the standard, and in accordance with prescribed procedures approved product drawings and technical documents manufacture. If you have special needs
According to the user and the manufacturer's agreement (contract) execution.
3.1.2
steering arm material can be cast, forged, forged steel 45,40Cr this standard recommended or 35CrMo, to ensure product design performance
Under conditions that allow the use of other materials is not lower than the mechanical properties of the above materials.
3.1.3
and steering output shaft or inside big hole and knuckle connecting involute splines, a single bond or cone, and ball steering mechanism link
Small stud connection tapered hole. Shall comply with GB/T 3478.1, GB/T 157, GB/T 1095, GB/T 1096, GB/T 1098 and
GB/T 1563 regulations. When using tapered spline connection, it is recommended to taper 1.16, spline tooth by the design requirements.
GB/T 19408.6-2020 | GB/T 21958-2017 | CNCA C11-06-2014 | GB/T 43478-2023 | GB/T 19040-2016 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 24652-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 24652-2009
$125.00