Valid

GB/T 24299-2009Test method for the mechanical life of snap action discs of thermostat bimetal (English PDF)

热双金属碟形元件机械寿命试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 24299-2009 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

September 30, 2009

Implementation date

February 1, 2010

Scope

GB/T 24299-2009 is the English-translated version of 热双金属碟形元件机械寿命试验方法.

GB/T 24299-2009 is the Chinese standard "Test method for the mechanical life of snap action discs of thermostat bimetal". Its scope clause reads: This standard specifies thermal bimetal disc element (hereinafter referred to as disc elements) Test Method and apparatus for mechanical life.

This standard applies to indirect heating, direct heating element mechanical life test disc and mixed under heating conditions of work. Its clauses include terms and definitions; test purpose and test conditions.

Found what you need?

Document preview — GB/T 24299-2009

National Standard of the People's Republic of China

ICS
29.120.20
Classification
H 21

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 Test purpose and test conditions

1 Scope

This standard specifies thermal bimetal disc element (hereinafter referred to as disc elements) Test Method and apparatus for mechanical life.

This standard applies to indirect heating, direct heating element mechanical life test disc and mixed under heating conditions of work.

2 Normative references

The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent

Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research

Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.

GB/T 2900.18 Electrotechnical term low-voltage electrical

3 Terms and Definitions

In addition to this standard the terms and definitions GB/T 2900.18 provisions, but also uses the following terms and definitions.

3.1

Machined from hot metal into a double disc member, when the temperature changes up and down within a predetermined range, the uneven surface reversibly projecting in opposite directions

Jump action.

3.2

Dished element in the product standard temperature range, with the uneven surface temperature change reversible kick action when there is no load cycle

Ring count.

3.3

Disc member through a heating operation starts immediately and subsequent action of a cool reply.

4 Test purpose and test conditions

4.1 Test Purposes

Disc detection element operating cycles (mechanical life) under no-load conditions.

4.2 Test conditions

4.2.1

test to detect the temperature deviation should not exceed the take-off before the test temperature jump of 5%, or no more than 6 °C, both the larger election

Comparison.

4.2.2

This standard uses air heating, adjustable air flow through the temperature of the heating or cooling element disc.

4.2.3

When the air flow temperature should not be higher than the temperature of the test disc element starts 10 °C, special requirements agreed by manufacturers and users.

4.2.4

Test operating cycles per hour is preferably not more than 12 times. In order to shorten the test time, allow an increase in the operating cycle frequency, specific

Specified by the manufacturer.

4.2.5

Test principle diagram shown in Figure 1.

GB/T 20831-2025 | GB/T 23365-2023 | GB/T 24488-2021 | GB/T 13221-2026 | GB/T 24298-2009 | GB/T 24297-2009 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 24299-2009

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 24299-2009

$95.00