GB/T 23126-2008Low pressure sodium lamps -- Performance requirement (English PDF)
低压钠灯 性能要求
This is a limited preview
Buy now to download the full PDF (18 pages)
Need quotation for your management?
Get a formal quotation for GB/T 23126-2008 in 30 minutes.
Issued by
Standardization Administration of China
Level / Type
National · Recommended
Issue date
December 30, 2008
Implementation date
September 1, 2009
Scope
GB/T 23126-2008 is the English-translated version of 低压钠灯 性能要求.
GB/T 23126-2008 — This standard specifies the low-pressure sodium lamps for general lighting performance requirements. For the requirements given in this standard can be found in the relevant lamp "Parameter List."
This standard includes the parameters of these lights. For part of this standard Other light range, the relevant parameters provided by the lamp manufacturer or distributor.
The requirements of this standard relate only to type testing. Note. the requirements of this standard and the test type test sample to allow consistent and tolerance were submitted by the manufacturer carried out.
In principle this type test sample Product manufacturer shall have the typical characteristics of a set of sample composition, and should be as close to the center value of the product.
It is expected that the use of tolerances given in this standard and in accordance with the type test sample products produced will meet the standards of most products.
However, since the product the majority, and sometimes there will inevitably be a range of products exceeds a predetermined tolerance value. Sampling methods and properties tested in accordance with the guidance note, see IEC 60410.
Found what you need?
Document preview — GB/T 23126-2008
National Standard of the People's Republic of China
- ICS
- 29.140.30
- Classification
- K 71
Issued by: Standardization Administration of China
Contents
- What this standard covers1
- Document data2
- Standards quoted by this document3
What this standard covers
This standard specifies the general low pressure sodium lighting performance requirements. The requirements given in this standard, see the relevant lamp " parameter table. " This standard includes the parameters of these lights. For the scope of this standard and other lights, the relevant parameters by the lamp manufacturer or reseller. The requirements of this standard relate only to type testing. Note: The requirements of this standard and tolerances are submitted by the manufacturer and type test sample tests conducted consistent. In principle this type of test sample shall have the typical characteristics of manufacturer's products consisting of a set of samples, and should be as close as possible to the center value of the product. It can be expected, the use of tolerances given in this standard and in accordance with the type test samples made ??products would meet the criteria for most products. However, due to the vast range of products, and sometimes there will inevitably exceed the specified tolerance value products. On sampling methods and in accordance with the characteristics of inspection guidance notes, see IEC 60410.
Document data
International classification (ICS): 29.140.30.
Chinese classification (CCS): K71.
Estimated length of the Chinese original: 27,276 words.
Adopted international standard: IEC 60192-2001, MOD.
Standards quoted by this document
GB/T 1406.1; GB/T 1406.5; GB/T 2828.1; GB/T 2829; GB/T 2900.65; GB/T 15042; GB 19652
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 18 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 1406.1Types and dimensions of lamp caps - Part 1: Screw caps
- GB/T 1406.1-2008Types and dimensions of lamp caps - Part 1: Screw caps
- GB/T 1406.5Types and dimensions of lamp caps - Part 5: Bayonet caps
- GB/T 1406.5-2008Types and dimensions of lamp caps - Part 5: Bayonet caps
- GB/T 2828.1Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
- GB/T 2828.1-2003Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
IEC 60061 · ISO 2859 · IEC 60050 · IEC 60923 · GB 19652 · GB 19652-2005 · IEC 62035
How to Download GB/T 23126-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 1406.1-2026 — Types and dimensions of lamp caps - Part 1: Screw caps
GB/T 1406.5-2026 — Types and dimensions of lamp caps - Part 5: Bayonet caps
GB/T 15042-2008 — Auxiliaries for lamps -- Ballasts for discharge lamps (excluding tubular fluorescent lamps) -- Performance requirements
Secure payment via Stripe
Payments accepted
GB/T 23126-2008
$614.00