GB/T 22696.5-2011Electrical equipment safety - Risk assessment and risk reduction - Part 5: Method and example for risk assessment and reduction (English PDF)
电气设备的安全 风险评估和风险降低 第5部分：风险评估和降低风险的方法示例
This is a limited preview
Buy now to download the full PDF (20 pages)
Need quotation for your management?
Get a formal quotation for GB/T 22696.5-2011 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 29, 2011
Implementation date
December 1, 2011
Scope
GB/T 22696.5-2011 is the English-translated version of 电气设备的安全 风险评估和风险降低 第5部分：风险评估和降低风险的方法示例.
GB/T 22696.5-2011 is the Chinese standard "Electrical equipment safety - Risk assessment and risk reduction - Part 5: Method and example for risk assessment and reduction".
Its scope clause reads: section gives a basis GB/T 22696.1 ~ 22696.4 pairs of electrical equipment implementation guide risk assessment for risk Each evaluation process, the specific operation steps of methods and tools, and gives examples.
Users expect 1.2 section is about the safety of electrical equipment into the design, manufacture, installation, maintenance or improvement of the designers, technical Or security standards experts.
Except for the part of the design phase as well as manufacture and commissioning process of security risk assessment, electrical equipment modifications or process improvement There can also be a security risk assessment, or evaluation of existing electrical equipment.
No risk assessment requirements or manufacturer's decision in product-related standards Given the case without the use of relevant standards, this section may provide guidance to manufacturers in product design.
Its clauses include terms and definitions; steps and methods of risk assessment process.
Found what you need?
Document preview — GB/T 22696.5-2011
National Standard of the People's Republic of China
- ICS
- 29.020
- Classification
- K 09
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4.1 Overview
- 4.2 Information for risk assessment
- 4.3 Electrical equipment limitations determined
- 4.4 Hazard Identification
- 5 4.5 Evaluation of the severity of injury
- 4.7 avoid the possibility of injury
- 4.8 Estimated risk
- 4.9 Risk Reduction
- References
1 Scope
1.1
section gives a basis GB/T 22696.1 ~ 22696.4 pairs of electrical equipment implementation guide risk assessment for risk
Each evaluation process, the specific operation steps of methods and tools, and gives examples.
Users expect 1.2 section is about the safety of electrical equipment into the design, manufacture, installation, maintenance or improvement of the designers, technical
Or security standards experts.
1.3
Except for the part of the design phase as well as manufacture and commissioning process of security risk assessment, electrical equipment modifications or process improvement
There can also be a security risk assessment, or evaluation of existing electrical equipment. No risk assessment requirements or manufacturer's decision in product-related standards
Given the case without the use of relevant standards, this section may provide guidance to manufacturers in product design.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
Security risk assessment and risk reduction GB/T 22696.1-2008 Electrical Equipment Part 1. General
GB/T 22696.2-2008 security risk assessment and risk reduction in electrical equipment - Part 2. Risk analysis and risk assessment
GB/T 22696.3-2008 security risk assessment and risk reduction in electrical equipment - Part 3. danger, peril and danger
Example risk event
Security risk assessment and risk reduction GB/T 22696.4-2011 electrical equipment Part 4. Risk Reduction
3 Terms and Definitions
Terms and definitions GB/T 22696.1-2008 and GB/T 22696.4-2011 defined apply to this document.
4 steps and methods of risk assessment process
4.1 Overview
This section explains the steps and methods of risk assessment process for electrical equipment or products in the design, manufacture, installation, operation, maintenance, and finally
Risk assessment only and so the whole life cycle, raise sufficient information to conduct a risk assessment based on GB/T 22696.1 principle, complete application
The whole concept and specific implementation methods.
4.2 Information for risk assessment
Information for risk assessment include. the use of electrical equipment environment, usage, functions, structure description, experience, skills
Surgery regulations, standards, pre-design.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 20 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 22696.5-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 22696.1-2008 — Electrical equipment safety - Risk assessment and risk reduction - Part 1: General requirements
GB/T 22696.2-2008 — Electrical equipment safety - Risk assessment and risk reduction - Part 2: Risk analysis and risk evaluation
GB/T 22696.3-2008 — Electrical equipment safety - Risk assessment and risk reduction - Part 3: Example of hazards, hazardous situations and hazardous events
Secure payment via Stripe
Payments accepted
GB/T 22696.5-2011
$345.00