Valid

GB/T 18011-2008Natural rubber latex concentrate -- Preparation of dry films (English PDF)

Preview PDF

This is a limited preview

Buy now to download the full PDF (5 pages)

Need quotation for your management?

Get a formal quotation for GB/T 18011-2008 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine of PRC. Standardization Administratio

Level / Type

National · Recommended

Issue date

May 15, 2008

Implementation date

November 1, 2008

Scope

GB/T 18011-2008 (Natural rubber latex concentrate -- Preparation of dry films) is available as an English-translated PDF.

GB/T 18011-2008 — This standard specifies the method for preparing a homogeneous dry rubber film without air bubbles, from natural rubber latex concentrate. This standard applies to Hevea brasiliensis latex.

It is not necessarily suitable for other natural latex, compound latex, vulcanized latex, water cement, synthetic latex.

Found what you need?

Document preview — GB/T 18011-2008

National Standard of the People's Republic of China

ICS
83.060
Classification
B 72

Issued by: General Administration of Quality Supervision, Inspection and Quarantine of PRC. Standardization Administratio

Contents

  • Foreword...3
  • 1 Scope...4
  • 2 Normative references...4
  • 3 Equipment...4
  • 4 Sampling...5
  • 5 Operation steps...5

Foreword

This standard is identically translated from ISO 498:1992 "Natural rubber latex

concentrate - Preparation of dry films" (English version).

For ease of use, this standard has made the following editorial changes:

- CHANGE the words "this International Standard" into "this Standard";

- DELETE the foreword of the International Standard.

- MAKE references to GB/T 8290 and GB/T 8298 in the normative references in

Chapter 2. There is no technical difference between these two standards and the

corresponding parts of ISO 498:1992.

This standard replaces GB/T 18011-1999 "Natural rubber latex concentrate -

Preparation of dry films".

The main differences between this standard and GB/T 18011-1999 are as follows:

- DELETE the ISO foreword;

- MAKE editorial revisions, in accordance with the provisions of GB/T 1.1-2000 and

GB/T 20001.4-2001.

This standard was proposed by China Petroleum and Chemical Industry Association.

This standard shall be under the jurisdiction of the Natural Rubber Subcommittee of the

National Rubber and Rubber Standardization Technical Committee.

Drafting organizations of this standard: Institute of Agricultural Products Processing of

Chinese Academy of Tropical Agricultural Sciences, Food Quality Supervision,

Inspection and Testing Center (Zhanjiang) of Ministry of Agriculture.

1 Scope

This standard specifies the method for preparing a homogeneous dry rubber film

without air bubbles, from natural rubber latex concentrate.

This standard applies to Hevea brasiliensis latex. It is not necessarily suitable for other

natural latex, compound latex, vulcanized latex, water cement, synthetic latex.

2 Normative references

The provisions in following documents become the provisions of this Standard through

reference in this Standard. For the dated references, the subsequent amendments

(excluding corrections) or revisions do not apply to this Standard; however, parties who

reach an agreement based on this Standard are encouraged to study if the latest versions

of these documents are applicable. For undated references, the latest edition of the

referenced document applies.

GB/T 8290 Natural rubber latex concentrate - Sampling (GB/T 8290-1987, eqv ISO

123:1985)

GB/T 8298 Natural rubber latex concentrate - Determination of total solids content

(GB/T 8298-2008, ISO 124:1997, MOD)

3 Equipment

3.1 Mold: It can be made by bonding glass or hard plastic sheets, which have a width

of 6 mm and a thickness of 1.5 mm, to a glass plate. The adhesive is epoxy resin or

polyvinyl acetate solution in methyl ethyl ketone. The size of the mold cavity depends

on the requirements of the test sample, for example, the length is 150 mm ~ 200 mm,

the width is 110 mm ~ 120 mm. When the mold is filled with latex, which has a total

solid content of 62% (mass fraction), the thickness of the prepared dry film is about 1

mm.

......

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 5 pages — is available in the English PDF.

Referenced standards

How to Download GB/T 18011-2008

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Instant delivery (0–9 sec)

    Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
5 pages
Instant delivery (0–9 sec)
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 18011-2008

$45.00