Valid

GB/T 17492-2019Industrial woven wire cloth - Technical requirements and tests (English PDF)

工业用金属丝编织网技术要求和检验

Preview PDF

This is a limited preview

Buy now to download the full PDF (30 pages)

Need quotation for your management?

Get a formal quotation for GB/T 17492-2019 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

December 10, 2019

Implementation date

July 1, 2020

Scope

GB/T 17492-2019 is the English-translated version of 工业用金属丝编织网技术要求和检验.

GB/T 17492-2019 is the Chinese standard "Industrial woven wire cloth - Technical requirements and tests". Its scope clause reads: This standard specifies the terms and definitions, technical requirements, inspection methods, and quality documents for industrial wire woven meshes used for screening and filtration.

Items, ordering information, and shipping. This standard applies to industrial wire woven square hole mesh made of steel, stainless steel or non-ferrous metals.

This standard does not apply to wire-plated wire mesh, pre-bent wire-woven mesh, and wire-welded mesh after weaving. Wire woven mesh for screening and filtering purposes can refer to the use of this standard.

When ordering, the supply and demand sides negotiate to determine specific technical requirements. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 17492-2019

National Standard of the People's Republic of China

ICS: 19.120
Classification: A 28

Issued by: State Administration for Market Regulation, China National Standardization Administration

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Technical requirements
4.1 Combination of mesh size and wire diameter
4.2 Mesh Size Tolerance
4.3 Permitted number of major defects
4.4 Maximum allowable deviation of overall dimensions
4.5 Flatness
4.6 Appearance
4.7 Wire
5 Inspection method
5.1 Wire diameter
5.2 Mesh size
5.3 Material composition
5.4 Overall dimensions
5.5 Weaving defects
6 Quality documents
6.1 Certificate of conformity
6.2 Test report
6.3 Third party inspection report
6.4 Chemical analysis
6.5 Other tests
7 Ordering Information
7.1 Basic information
7.2 Additional information
8 Ships
8.1 Net Volume
8.2 Packaging
8.3 Marker
Appendix A (Informative) Major Defects
Appendix B (informative) Calculation of the average mesh size and standard deviation
Appendix C (informative) Interpolation calculation of mesh size limit standard deviation s0

1 Scope

This standard specifies the terms and definitions, technical requirements, inspection methods, and quality documents for industrial wire woven meshes used for screening and filtration.

Items, ordering information, and shipping.

This standard applies to industrial wire woven square hole mesh made of steel, stainless steel or non-ferrous metals.

This standard does not apply to wire-plated wire mesh, pre-bent wire-woven mesh, and wire-welded mesh after weaving.

Wire woven mesh for screening and filtering purposes can refer to the use of this standard. When ordering, the supply and demand sides negotiate to determine specific technical requirements.

2 Normative references

The following documents are essential for the application of this document. For dated references, only the dated version applies to this article

Pieces. For undated references, the latest version (including all amendments) applies to this document.

GB/T 5330.1 Industrial Wire Mesh and Wire Woven Mesh Selection Guide for Combination of Mesh Size and Wire Diameter Part 1

Part. General (GB/T 5330.1-2012, ISO 4783-1. 1989, MOD)

GB/T 10611 Industrial marking method and mesh size series (GB/T 10611-2003, ISO 2194..1991, MOD)

GB/T 19628.2-2005 Industrial Wire Mesh and Wire Woven Mesh Selection Guide for Combination of Mesh Size and Wire Diameter

Selection of preferred combinations of wire meshes (ISO 4783-2. 1989, MOD)

JB/T 7860-2000 Industrial wire

3 terms and definitions

The following terms and definitions apply to this document.

3.1 Mesh size aperturewidth

The distance between adjacent warp or weft threads.

Note. Measure in the middle of the projection plane mesh, see Figure 1.

GB/T 6003.2 | GB/T 19077 | GB/T 6003.1 | GB/T 21650.1 | GB/T 45322.3 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 30 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 4783 · ISO 2194

Cited by

How to Download GB/T 17492-2019

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.