Valid

TB/T 2140-2008Railway ballast (English PDF)

Preview PDF

This is a limited preview

Buy now to download the full PDF (22 pages)

Need quotation for your management?

Get a formal quotation for TB/T 2140-2008 in 30 minutes.

Issued by

National Railway Administration of PRC 3. No action is required - Full-copy of this standard will be automatic

Level / Type

National · Recommended

Issue date

September 15, 2015

Implementation date

April 1, 2016

Scope

TB/T 2140-2008 (Railway ballast) is available as an English-translated PDF.

TB/T 2140-2008 — This Part of TB/T 2765 specifies the record mode, record items, record item points, record generated conditions, dumping and data processing of recording of the train monitoring device (can be expressed by LKJ).

This Part is applicable to the train monitoring device (hereinafter referred to as device) on the locomotive, bullet train and self-rotating wheel running equipment.

Found what you need?

Document preview — TB/T 2140-2008

National Standard of the People's Republic of China

ICS: 29.280
Classification: S 35

Issued by: National Railway Administration of PRC 3. No action is required - Full-copy of this standard will be automatic

Foreword...3
1 Scope...4
2 Normative References...4
3 Record Mode...4
4 Record Items...4
5 Record Item Points...5
6 Record Generation Conditions...6
7 Dumping of the Recording...7
8 Data Processing of the Recording...7
Appendix A (Informative) Device Recording...8
Table A.1 -- Overhaul Parameter Information...8
Table A.2 -- Setting Relevant Parameter Information...9
Table A.3 -- Locomotive/Bullet Train Condition Information...9
Table A.4 -- Bullet Train Information...11
Table A.5 -- Other ATP Information...12
Table A.6 -- GPS Relevant Information...14
Table A.7 -- Other Collecting Information...15
Table A.8 -- Key Information...15
Table A.9 -- Brake Test State Information...17
Table A.10 -- Running State Information...17
Table A.11 -- Software Version Information...22

Foreword

TB/T 2765 Train Monitoring Device can be divided into 5 parts.

--- Part 1. Technical Conditions;

--- Part 2. Recording;

--- Part 3. Regulations on Voice and Electronic Beeping;

--- Part 4. Special IC Card;

--- Part 5. Adjusting Light Display Interface Box.

This Part belongs to Part 2 of TB/T 2765 Train Monitoring Device.

This Part was drafted as per the rules specified in GB/T 1.1-2009.

This Part shall be under the jurisdiction of CRRC Zhuzhou Institute Co., Ltd.

Chief Drafting organizations of this Part. CRRC Zhuzhou Institute Co., Ltd.

Participating drafting organizations of this Part. Henan Thinker Automatic Equipment

Co., Ltd.

Chief drafting staffs of this Part. Shen Zhulin, and Zhang Jiahuan.

Participating drafting staffs of this Part. Yang Qingxiang, and Yang Lijun.

Training Monitoring Device – Part 2. Recording

1 Scope

This Part of TB/T 2765 specifies the record mode, record items, record item points,

record generated conditions, dumping and data processing of recording of the train

monitoring device (can be expressed by LKJ).

This Part is applicable to the train monitoring device (hereinafter referred to as device)

on the locomotive, bullet train and self-rotating wheel running equipment.

2 Normative References

The following documents are essential to the application of this document. For the

dated documents, only the versions with the dates indicated are applicable to this

document; for the undated documents, only the latest version (including all the

amendments) are applicable to this document.

TB/T 2765.1-2015 Train Monitoring Device – Part 1. Technical Conditions

3 Record Mode

3.1 The recording shall be stored and managed in the document mode.

3.2 Software information collection adopts variable record mode; when the

information collected reaches specified condition, the corresponding record shall be

generated.

3.3 When the variation of information collected during one record period exceeds the

specified interval, only record once change of the information collected. The record

period shall be no greater than 2s.

4 Record Items

4.1 Input information

The input information indicates the overhaul parameters inputted to the device, setting

relevant parameters and the like information; which mainly include locomotive model,

locomotive number, wheel diameter, driver number, train number, train marshalling,

g) Train tube pressure, equalizing reservoir pressure, locomotive brake cylinder

pressure, accuracy of 10kPa;

h) Locomotive running condition information (traction/brake position, zero position,

forward/backward position and diesel engine speed, etc.).

5.2 The recording shall record the item points beyond 5.1, it can supplement other

item points, such as input contents, software version, etc.

5.3 When the transportation requirements change, it shall increase or decrease the

record items and item points through the negotiation between the supplier and the

purchaser.

6 Record Generation Conditions

6.1 For the record items of the input information, when detecting the input information

is changed, corresponding records shall be generated.

6.2 For the record items of the information collection, when the change of information

collection reaches the specified conditions, it shall generate corresponding records;

thereof the mainly specified conditions are as follows.

a) Each time when the collected speed changes greater than or equal to 2km/h or

declines to 0km/h;

b) In the stopping state, each time when the collected pressure changes greater

than or equal to 40kPa; in the non-stopping state, each time when the collected

pressure changes greater than or equal to 20kPa; the collected pressure

declines to 0kPa.

c) Each time when the collected rotation speed of diesel engine changes greater

than or equal to 40r/min.

d) When the collected locomotive signal status changes.

e) When the collected locomotive running conditions (traction/brake position, zero

position, forward/backward position) change.

6.3 For the record items of operation information, when the device detects the

effective operation information, corresponding records shall be generated.

6.4 For the record items of running status information, when the running status of the

device conforms to the specified record conditions, the corresponding records shall be

generated.

6.5 For the record items of the version information, each time the document is

17 Terminal-II beep ending

Device detects the Terminal-

II beep ending information

When device detecting the Terminal-II beep information

from invalid to valid

18 Terminal-I electric horn beep ending

Device detects the Terminal-I

electric horn beep ending

information

When device detecting the Terminal-I electric horn beep

information from invalid to valid

19 Terminal-II electric horn beep ending

Device detects the Terminal-

II electric horn beep ending

information

When device detecting the Terminal-II electric horn

beep information from invalid to valid

Main circuit-

breaker

disconnecting

Device detects the main

circuit-breaker disconnecting

information

When device detects the main circuit-breaker state from

connecting to disconnecting

Main circuit-

breaker

connecting

Device detects the main

circuit-breaker connecting

information

When device detects the main circuit-breaker state from

disconnecting to connecting

Auto-passing

phase separation

predicted

interruption

starting

Device detects the auto-

passing phase separation

predicted interruption starting

information

When device detecting the auto-passing phase

separation predicted interruption information starts

Auto-passing

phase separation

predicted

interruption

ending

Device detects the auto-

passing phase separation

predicted interruption ending

information

When device detecting the auto-passing phase

separation predicted interruption information ends

Auto-passing

phase separation

forced interruption

starting

Device detects the auto-

passing phase separation

forced interruption starting

information

When device detecting the auto-passing phase

separation forced interruption information starts

Auto-passing

phase separation

forced interruption

ending

Device detects the auto-

passing phase separation

forced interruption ending

information

When device detecting the auto-passing phase

separation forced interruption information ends

Table A.4 -- Bullet Train Information

SN Names of Record Items Meanings of Record Items Record Time

1 Communication failure with EMU

Device detects the

communication interruption

with EMU

When device detects the communication failure with

EMU equipment

Communication

restoration with

EMU

Device detects the

communication restoration

with EMU

When device detects the communication with EMU

equipment is restored normally

3 EMU brake pressure

Device receives the EMU

brake cylinder pressure

When device re...

......

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 22 pages — is available in the English PDF.

Referenced standards

Normative references

TB/T 2765.1-2015

How to Download TB/T 2140-2008

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.