NB/T 47045-2015Brazed plate heat exchanger (English PDF)
钎焊板式热交换器
This is a limited preview
Buy now to download the full PDF (19 pages)
Need quotation for your management?
Get a formal quotation for NB/T 47045-2015 in 30 minutes.
Issued by
NEA
Level / Type
Industry · Recommended
Issue date
April 2, 2015
Implementation date
September 1, 2015
Scope
NB/T 47045-2015 is the English-translated version of 钎焊板式热交换器.
NB/T 47045-2015 is the Chinese standard "Brazed plate heat exchanger". Its scope clause reads: This standard specifies the technical requirements, such as design, material, fabrication, inspection, acceptance, marking and packaging, of the brazed plate heat exchangers.
This standard is applicable to brazed plate heat exchangers with a working temperature of -196°C~225°C and a working pressure of -0.1 MPa~14 MPa. For brazed plate heat exchangers beyond the scope of this standard, it shall be determined by the evaluation of technical evaluation institutions. Its clauses include terms and definitions.
Found what you need?
Document preview — NB/T 47045-2015
National Standard of the People's Republic of China
Issued by: National Energy Administration of the People's Republic of China
Contents
- Foreword i
- Introduction ii
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 General requirements
- 5 Materials
- 6 Design
- 7 Fabrication
- 8 Inspection and acceptance
- 9 Marking and packaging
- 10 Installation and use
- Annex A (Informative) Instruction for brazing procedure and brazing procedure qualification report
- Annex B (Informative) Fatigue test report
1 Scope
1.1
This standard specifies the technical requirements, such as design, material, fabrication, inspection, acceptance, marking and packaging, of the brazed plate heat exchangers.
1.2
This standard is applicable to brazed plate heat exchangers with a working temperature of -196°C~225°C and a working pressure of -0.1 MPa~14 MPa.
1.3
For brazed plate heat exchangers beyond the scope of this standard, it shall be determined by the evaluation of technical evaluation institutions.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 1220 Stainless steel bars
GB/T 3280 Cold rolled stainless steel plate, sheet and strip
GB/T 4237 Hot rolled stainless steel plate, sheet and strip
GB/T 5187 Foil of copper and copper alloy
GB 13296 Seamless stainless steel tubes for boiler and heat exchanger
GB 24511 Stainless steel plate, sheet and strip for pressure equipment
NB/T 47013.5 Nondestructive testing of pressure equipments - Part 5: Penetrant testing
NB/T 47004 Plate heat exchangers
NB/T 47008 Carbon and alloy steel forgings for pressure equipment
NB/T 47010 Stainless and heat-resisting steel forgings for pressure equipment
NB/T 47014 Welding procedure qualification for pressure equipment
NB/T 47018 Technical permission of welding materials for pressure equipment
3 Terms and definitions
For the purposes of this document, the terms and definitions given in NB/T 47004 and the following apply.
3.1 pressure
force acting on unit area vertically, which refers to gauge pressure hereof, unless otherwise specified
3.2 working pressure
maximum pressure possibly existing on any side of brazed plate heat exchanger under normal operating condition
3.3 design pressure
maximum pressure set on any side of brazed plate heat exchanger, which is used as design load conditions together with the corresponding design temperature and shall not be less than the working pressure
3.4 design temperature
element temperature of brazed plate heat exchanger set under normal working pressure and corresponding design pressure
In any case, the temperature of element surface shall not exceed the allowable service temperature of element material. For the brazed plate heat exchangers working at a temperature above 0°C, the design temperature shall not be lower than the possible maximum temperature of element surface under working condition; for those working at a temperature below 0°C, the design temperature shall not be higher than the possible minimum temperature of element surface.
3.5 bursting pressure
maximum pressure of brazed plate heat exchanger during burst test
3.6 plate
corrugated metal plate formed by precise pressing
3.7 endplate
plate at the end face side of brazed plate heat exchanger which plays a reinforcing role
3.8 plate pack
set of all the plates contained between the endplates
3.9 brazed plate heat exchanger
integrated heat exchanger formed by welding plates, endplates, nozzles or flanges at high temperature, as shown in Figure 1 […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 19 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download NB/T 47045-2015
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
NB/T 10186-2026 — Technical specification for power conversion equipment used in photovoltaic-storage systems
NB/T 11969-2026 — Guide for energy efficiency assessment of off-board conductive chargers for electric vehicles
NB/T 11970-2026 — Specification for operation safety evaluation of grid-connected electric vehicle charging facilities
NB/T 47045-2015
$449.00