Valid

NB/T 47015-2011Welding Specification for pressure vessels (English PDF)

压力容器焊接规程

Preview PDF

This is a limited preview

Buy now to download the full PDF (33 pages)

Need quotation for your management?

Get a formal quotation for NB/T 47015-2011 in 30 minutes.

Issued by

NEA

Level / Type

Industry · Recommended

Issue date

July 1, 2011

Implementation date

October 1, 2011

Scope

NB/T 47015-2011 is the English-translated version of 压力容器焊接规程.

NB/T 47015-2011 is the Chinese standard "Welding Specification for pressure vessels". Its scope clause reads: This standard specifies the basic requirements for the welding of steel, aluminium, titanium, copper, nickel and composite metal pressure vessels.

This standard is applicable to the pressure vessels welded by gas welding, shielded metal arc welding, submerged-arc welding, gas tungstun arc welding, gas metal arc welding, plasma arc welding, electro-gas welding and stud welding.

This standard is not applicable to gas cylinder. Its clauses include general welding specification.

Found what you need?

Document preview — NB/T 47015-2011

National Standard of the People's Republic of China

Replacing
JB/T 4709-2000

Issued by: National Energy Administration of the People's Republic of China

Contents

  • Foreword I
  • 1 Scope
  • 2 Normative References
  • 3 General Welding Specification
  • 4 Welding Specification for Steel Pressure Vessels
  • 5 Welding Specification for Aluminium Pressure Vessels
  • 6 Welding Specification for Titanium Pressure Vessels
  • 7 Welding Specification for Copper Pressure Vessels
  • 8 Welding Specification for Nickel Pressure Vessels
  • 9 Welding Specification for Composite Metal Pressure Vessels
  • Appendix A (Informative) Specified Method and Scope for Weld Position
  • Appendix B (Informative) Type and Dimension of Special Material Welding Groove
  • Appendix C (Informative) Recommended Table for Welding Process Specification
  • Explanation on Compilation

1 Scope

This standard specifies the basic requirements for the welding of steel, aluminium, titanium, copper, nickel and composite metal pressure vessels.

This standard is applicable to the pressure vessels welded by gas welding, shielded metal arc welding, submerged-arc welding, gas tungstun arc welding, gas metal arc welding, plasma arc welding, electro-gas welding and stud welding.

This standard is not applicable to gas cylinder.

2 Normative References

The following documents are indispensable for the application of this document. For dated references, only the dated edition applies. For undated references, the latest edition (including all the amendments) of the normative document applies.

GB/T 985.3 Recommended Joint Preparation for Gas-Shield Arc Welding on Aluminium and Its Alloys

GB/T 3670 Coated Electrodes for Copper and Copper Alloys

GB/T 9460 Copper and Copper Alloy Wires and Rods

NB/T 47002 (all parts) Explosion Welded Clad Plate for Pressure Vessels

NB/T 47014 Welding Procedure Qualification for Pressure Equipment

NB/T 47018 (all parts) Technical Permission of Welding Materials for Pressure Equipment

JB/T 4745 Titanium Welded Vessels

TSG 26002-2010 Regulations of Assessment on Special Equipment Welding Operation Personnel

3 General Welding Specification

3.1 General requirements

3.1.1

The welding of pressure vessels shall not only comply with the requirements of this standard, but also shall meet the technical requirements of design document.

3.1.2

In addition to the requirements of this standard, the achievements that are proven to be effective through experimental study and practices may be used for the welding of pressure vessels after being approved by the relevant parties and listed in the enterprise standards.

3.2 Welding materials

3.2.1

Welding materials include welding electrode, welding wire, solder strip, flux, gas, electrode and gasket, etc.

3.2.2

Selection principles for welding materials:

a) The mechanical properties of weld metal shall be higher than or equal to the specified limit of base metal; where it is necessary, other properties shall not be lower than the corresponding requirements of base metal; or the mechanical properties and other properties shall meet the technical requirements specified in the design document;

b) Suitable welding materials shall match the reasonable welding process to ensure that the properties of welded joint can still meet the requirements of design document and service after undergoing manufacturing process;

c) The manufacturing (installation) organization shall know the welding property of welding materials; the welding materials used for pressure vessels shall have welding test or practice basis.

3.2.3

The welding materials used for pressure vessels shall be in accordance with those specified in NB/T 47018.

3.2.4

Welding materials shall be provided with product quality certification and shall meet the requirements of relevant standards. The using organization shall carry out acceptance or reinspection according to the requirements of quality management system and relevant standards, and the welding materials may be used after passing the acceptance or reinspection.

3.3

Weld positions are classified into flat weld, vertical weld, horizontal weld and overhead weld. See Appendix A for the specified method and scope for weld position.

3.4 Welding process qualification and welders

3.4.1

The welding process for welding the following welds shall be qualified through assessment according to NB/T 47014:

a) Weld of pressure parts;

b) Weld welded with pressure parts;

c) Tack weld of the above-mentioned ones.

d) Surface overlaying and repair welding of the base metal of pressure parts.

3.4.2

The welder welding the following welds shall be pass the examination according to TSG 26002:

a) Weld of pressure parts;

b) Weld welded with pressure parts;

c) Tack weld permanently fused into the above-mentioned permanent welds;

d) Surface overlaying and repair welding of the base metal of pressure parts.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 33 pages — is available in the English PDF.

Referenced standards

Similar standards

Editions of NB/T 47015

EditionTitleRevisionStatus
NB/T 47015-2011Welding Specification for pressure vesselscurrent editionCurrent
JB/T 4709-2000Welding Specification for pressure vesselsprevious editionSuperseded

This page sells the current edition, NB/T 47015-2011. Earlier editions are listed for reference only.

How to Download NB/T 47015-2011

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
33 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

NB/T 47015-2011

$185.00