Valid

NB/T 47008-2010Carbon and alloy steel forgings for pressure equipments (English PDF)

承压设备用碳素钢和合金钢锻件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for NB/T 47008-2010 in 30 minutes.

Issued by

NEA

Level / Type

Industry · Recommended

Issue date

August 27, 2010

Implementation date

December 15, 2010

Scope

NB/T 47008-2010 is the English-translated version of 承压设备用碳素钢和合金钢锻件.

NB/T 47008-2010 is the Chinese standard "Carbon and alloy steel forgings for pressure equipments". Its scope clause reads: This standard specifies the technical requirements, test methods and inspection rules, etc. for carbon steel and alloy steel forgings for pressure equipments.

This standard is applicable to carbon steel and alloy steel forgings for pressure equipments with a design temperature not less than -20°C and design pressure below 100Mpa.

Its clauses include terms and definitions; ordering information; technical requirements.

Found what you need?

Document preview — NB/T 47008-2010

National Standard of the People's Republic of China

Replacing
JB 4726-2000

Issued by: National Energy Administration of the People's Republic of China

Contents

  • Foreword I
  • 1 Scope
  • 2 Normative References
  • 3 Terms and Definitions
  • 4 Ordering Information
  • 5 Technical Requirements
  • 6 Test Methods
  • 7 Inspection Rules
  • 8 Marking and Quality Certificate
  • Appendix A (Normative) Additional Requirements

1 Scope

This standard specifies the technical requirements, test methods and inspection rules, etc. for carbon steel and alloy steel forgings for pressure equipments.

This standard is applicable to carbon steel and alloy steel forgings for pressure equipments with a design temperature not less than -20°C and design pressure below 100Mpa.

2 Normative References

The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, only the dated versions apply to this standard. For undated references, the latest edition of the normative document (include all the amendments) is applicable to this standard.

GB/T 222-2006 Permissible Tolerances for Chemical Composition of Steel Products

GR/T 223 Methods for Chemical Analysis of Iron, Steel and Alloy

GB/T 228 Metallic Materials-Tensile Testing at Ambient Temperature (ISO 6892:1998 (E))

GBIT/229-2007Metallic materials-Charpy pendulum impact test method (ISO 148-1:2006)

GB/T 23 1.1 Metallic Materials-Vickers Hardness Test-Part 1: Test Method (1S0 6506-1:2005)

GB/T 4336 Standard Test Method for Spark Discharge Atomic Emission Spectrometric Analysis of Carbon and Low-Alloy Steel (Routine Method)

GB/T 4338 Metallic Materials-Tensile Testing at Elevated Temperature (ISO 783:1999)

GB/f 6394 Metal-methods for Estimating the Average Grain Size (ASTM E112:1996)

GB/T 10561 Steel-Determination of Content of Nonmetallic Inclusions-Micrographic Method Using Standards Diagrams (1S0 4967: 1998)

GB/T 20066 Steel and Iron-Sampling and Preparation of Samples for the Determination of Chemical Composition (IS0 14284:1996)

JB/T 4730.3 Non-destructive Testing of Pressure Equipment Part Three: Ultrasonic Testing

3 Terms and Definitions

This standard applies the following terms and definitions.

3.1 Hollow forging

It refers to axisymmetrical hollow forging, whose axial length L is greater than its outer diameter D, as shown in Fig. 1a). t shall be the nominal thickness.

3.2 Ring forging

It refers to axisymmetrical hollow forging, whose axial length L is less than or equal to its outer diameter D, as shown in Fig. 1b). The smaller one of L and t shall be the nominal thickness.

3.3 Disk forging

It refers to axisymmetrical solid forging, whose axial length l is less than or equal to its outer diameter D, as shown in Fig. 1c). L shall be the nominal thickness. 3.4

Bowl forging

It refers to axisymmetrical forging with concave section, whose length H is less than or equal to its outer diameter D, as shown in Fig. 1d). The greater one between t1 and t2 shall be the nominal thickness.

3.5 Neck flange forging

It refers to axisymmetrical neck flange with two axial outside diameters, as shown in Fig. 1e). The greater one of t1 and t2 shall be the nominal thickness.

3.6 Bar forging

It refers to solid forging with circle section, whose axial length L is greater than its outer diameter D, as shown in fig. 1f). D shall be the nominal thickness.

Forging with rectangular section, whose length L is greater than its side lengths a, b, as shown in Fig. 1g). The smaller one of a and b shall be the nominal thickness.

4 Ordering Information

4.1

The Buyer shall indicate the standard number, steel grade, forging class, supply status and quantity, etc. in the order contract.

4.2

The Buyer shall provide order drawing.

4.3

When the additional requirements in Appendix A (Normative) of this standard and other requirements, which exceed or are higher than this standard are used, they shall be indicated in the order contract by the Buyer.

5 Technical Requirements

5.1 Smelting process

Steel for forging shall be the killed steel smelted by electric furnace, oxygen converter. Smelting methods, such as electroslag remelting, external furnace refining may be used through mutual consultation.

5.2 Chemical composition

5.2.1

The chemical composition (heat analysis) of steel for forging shall comply with the stipulations in Table 1.

5.2.2

It is noted in the contract that P and s contents of 20, 35 and 16Mn steels may be p<=0.025% and S<=0.015% As required by the Buyer.

5.2.3

The Buyer may carry out product analysis, the permissible deviation between the analysis results and the specified values in Table 1 shall comply with the stipulations in Table 2 of GB/T 222. The permissible positive deviation is 0.003% for the steel grade of p<=0.020% in Table 1; the permissible positive deviation is 0.002% for steel type of S<=0.012%.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

Editions of NB/T 47008

EditionTitleRevisionStatus
NB/T 47008-2010Carbon and alloy steel forgings for pressure equipmentscurrent editionCurrent
JB 4726-2000Carbon and alloy steel forgings for pressure equipmentsprevious editionSuperseded

This page sells the current edition, NB/T 47008-2010. Earlier editions are listed for reference only.

How to Download NB/T 47008-2010

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

NB/T 47008-2010

$95.00