JB/T 4220-2011Determination method of lattice parameters of artificial graphite (English PDF)
人造石墨的点阵参数测定方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 4220-2011 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
December 20, 2011
Implementation date
April 1, 2012
Scope
JB/T 4220-2011 is the English-translated version of 人造石墨的点阵参数测定方法.
JB/T 4220-2011 is the Chinese standard "Determination method of lattice parameters of artificial graphite".
Its scope clause reads: This standard specifies the principle, internal standard materials, instruments, specimen preparation, test conditions, test steps, processing and calculation of test results and test report for determination of artificial graphite lattice parameter by X-ray powder diffraction method (diffractometer method).
The method is applicable to artificial graphite with high graphitization degree after high temperature heat treatment (such as graphite for artificial diamond).
Its clauses include principle; internal standard materials; instruments; specimen preparation.
Found what you need?
Document preview — JB/T 4220-2011
National Standard of the People's Republic of China
- ICS
- 29.120
- Replacing
- JB/T 4220-1999
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword i
- 1 Scope
- 2 Normative references
- 3 Principle
- 4 Internal standard materials
- 5 Instruments
- 6 Specimen preparation
- 7 Test conditions
- 8 Test steps
- 9 Processing and calculation of test results
- 10 Test report
- Annex A (Informative) Comparison between PB and g
1 Scope
This standard specifies the principle, internal standard materials, instruments, specimen preparation, test conditions, test steps, processing and calculation of test results and test report for determination of artificial graphite lattice parameter by X-ray powder diffraction method (diffractometer method).
The method is applicable to artificial graphite with high graphitization degree after high temperature heat treatment (such as graphite for artificial diamond).
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition applies.
JB/T 8133.1-1999 Test methods for physical-chemical properties of electric carbon products - Technical requirements for specimen processing
3 Principle
3.1
The graphitization degree of artificial graphite is a physical quantity and is usually measured by the size of the lattice parameter and expressed in the symbol PB.
3.2
The artificial graphite lattice parameter is defined in 3.2.1 to 3.2.4.
3.2.1 c0(002)
The c-axis length of the artificial graphite unit cell obtained from C(002) diffracted ray.
3.2.2 c0(004)
The c-axis length of the artificial graphite unit cell obtained from C(004) diffracted ray.
3.2.3 a0(110)
The a-axis length of the artificial graphite unit cell obtained from C(110) diffracted ray.
3.2.4 d112
The interplanar spacing d of the artificial graphite unit cell (112) obtained from C(112) diffracted ray.
3.3
The C(002), C(004), C(110) and C(112) diffraction patterns are recorded by an automatic X-ray diffractometer, the corresponding diffraction angle 2thetaCs is calculated by chord midpoint method, the respective diffraction angle 2thetaCj is calculated by internal standard method, and the corresponding artificial graphite lattice parameters c0(002), c0(004), a0(110) and d112 are obtained from the table. In addition, the graphitization degree PB is calculated using an equation from the lattice parameter c0(004).
4 Internal standard materials
Monocrystalline silicon powder (spectroscopically pure). Grind it with an agate mortar, and take the silicon powder passing through the 325-mesh (45µm) standard sieve as the internal standard materials for X-ray diffraction.
5 Instruments
Automatic X-ray diffractometer, using Cu-target X-ray tube.
6 Specimen preparation
6.1
Sampling method and sample size are subject to product standards.
6.2
Wipe the surface of the artificial graphite test block to be tested with alcohol cotton.
6.3
Crush the artificial graphite test block to be tested into powder with a hacksaw blade (or steel file) and let the powder pass through a 200-mesh (76µm) standard sieve. Take this powder as the specimen, and grind it with an agate mortar in case of too coarse grains.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Editions of JB/T 4220
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 4220-2011 | Determination method of lattice parameters of artificial graphite | current edition | Current |
| JB/T 4220-1999 | Determination method of lattice parameters of artificial graphite | previous edition | Superseded |
This page sells the current edition, JB/T 4220-2011. Earlier editions are listed for reference only.
How to Download JB/T 4220-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 8133.1-1999 — Test methods for physical and chemical properties of electrical carbon products - Technical rules for specimen preparation
JB/T 10062-2026 — Probes used in ultrasonic flaw detection - Testing methods for performance
JB/T 10096-2026 — Cases for power semiconductor devices - Selection guidance
JB/T 4220-2011
$195.00