Valid

JB/T 11798-2014Internal combustion engines - Heat exchangers - Wind tunnel test equipment (English PDF)

内燃机 换热器 风洞试验装置

Preview PDF

This is a limited preview

Buy now to download the full PDF (27 pages)

Need quotation for your management?

Get a formal quotation for JB/T 11798-2014 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

May 6, 2014

Implementation date

October 1, 2014

Scope

JB/T 11798-2014 is the English-translated version of 内燃机 换热器 风洞试验装置.

JB/T 11798-2014 is the Chinese standard "Internal combustion engines - Heat exchangers - Wind tunnel test equipment".

Its scope clause reads: This standard specifies the terms and definitions, symbols and interpretations, overall structure, technical requirements, measurement modules, test control and data acquisition modules, test data processing, validation and evaluation of wind tunnel for heat transfer, and marking, packaging, transport and storage of heat transfer wind tunnel test equipment for heat exchangers of internal combustion engines used in automobiles, tractors, construction machinery and small vessels.

This standard is applicable to test equipment for wind tunnel for heat transfer (hereinafter referred to as wind tunnel for heat transfer) for heat exchangers of internal combustion engines (including liquid-gas and gas-gas heat exchange) used in automobiles, tractors, construction machinery, and small vessels to conduct heat transfer performance tests.

It may be used as reference for the wind tunnel test equipment for heat exchangers of other purposes. Its clauses include terms and definitions.

Found what you need?

Document preview — JB/T 11798-2014

National Standard of the People's Republic of China

ICS
27.020

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword i
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Symbols and interpretations
  • 5 Overall structure
  • 5.1 General
  • 5.2 Negative pressure type wind tunnel for heat transfer
  • 5.3 The test section is in the inlet side air chamber
  • 5.5 Closed circulating wind tunnel for heat transfer
  • 6 Technical requirements
  • 6.1 Main module of negative pressure type wind tunnel for heat transfer
  • 6.2 Main module of air chamber type wind tunnel for heat transfer
  • 6.3 Closed circulating type wind tunnel for heat transfer
  • 6.4 Hot water module
  • 6.5 Hot oil module
  • 6.6 High temperature and high pressure air module
  • 7 Measurement module
  • 7.1 Test section temperature measurement
  • 7.2 Resistance measurement of test pieces from test section
  • 7.3 Flowrate measurement
  • 8 Test control and data acquisition module
  • 8.1 Measurement control precision
  • 8.2 Test medium
  • 8.3 Test procedure
  • 8.4 Test items
  • 9 Processing of test data
  • 9.1 Calculation of heat exchange capacity
  • 9.2 Calculation of the heat transfer coefficient
  • 9.3 Calculation of the conversion trans-heat
  • 9.4 Calculation of heat balance
  • 10 Validation and evaluation of wind tunnel for heat transfer
  • 10.1 General
  • 10.2 Standard samples
  • 10.3 Verification and evaluation rules
  • 11 Marking, packaging, transport and storage
  • 11.1 Marking
  • 11.2 Packaging
  • 11.3 Transport
  • 11.4 Storage of standard samples
  • 11.5 Others

1 Scope

This standard specifies the terms and definitions, symbols and interpretations, overall structure, technical requirements, measurement modules, test control and data acquisition modules, test data processing, validation and evaluation of wind tunnel for heat transfer, and marking, packaging, transport and storage of heat transfer wind tunnel test equipment for heat exchangers of internal combustion engines used in automobiles, tractors, construction machinery and small vessels.

This standard is applicable to test equipment for wind tunnel for heat transfer (hereinafter referred to as wind tunnel for heat transfer) for heat exchangers of internal combustion engines (including liquid-gas and gas-gas heat exchange) used in automobiles, tractors, construction machinery, and small vessels to conduct heat transfer performance tests. It may be used as reference for the wind tunnel test equipment for heat exchangers of other purposes.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 2624.3 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles

GB 11122-2006 Diesel engine oils

JJF 1059.1-2012 Evaluation and expression of uncertainty in measurement

JJG 667-2010 Liquid positive displacement flowmeter

JJG 1038-2008 Goriolis mass flow meters

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

3.1 wind tunnel for heat transfer

equipment for measuring the heat transfer performance and resistance performance of liquid-gas and gas-gas heat exchange devices

3.2 frontal area

the area of the windward side of the core of a heat exchanger with air as the cooling medium

3.3 effectiveness

the ratio of the actual heat exchange capacity of the heat exchanger to the maximum possible heat exchange capacity under the same conditions

3.4 hot side

the channel through which water flows in the water radiator, the channel through which oil flows in the oil radiator, and the channel through which charge air flows in the air-to-air intercooler

3.5 cool side

the channel through which normal pressure air flows in water radiator, oil radiator, and air-to-air intercooler

3.6 conversion trans-heat

the trans-heat at set temperature difference (the difference between the designated inlet temperature of high-temperature medium and low-temperature medium) converted from the actual trans-heat under the test condition, and it is also called the standard trans-heat

3.7 pressure drop

the static pressure difference formed by the test medium before and after flowing through the heat exchanger under the test condition, and it is also called resistance or working resistance

3.8 standard air

the air under the condition with the temperature of 20°C and the pressure of 101.3 kPa

3.9 accuracy

the ability of an instrument to indicate or record a measured truth value, expressed by the difference between the indicated value and the truth value

3.10 precision

under the same conditions and repeated measurements of the same physical quantity using the same method, the degree that the obtained indication values are close to the same

3.11 absolute pressure

the pressure measured with absolute vacuum as the measurement reference

3.12 mass flowrate

the mass of medium flowing through the specified section per unit time

3.13 volume flowrate

the volume of medium flowing through a specified section per unit time

3.14 velocity

under the test condition, the air velocity at a certain point on the frontal surface of the heat exchanger

3.15 average velocity

under the test condition, the weighted average air velocity on the frontal surface of the heat exchanger

3.16 correlation coefficient

a measure of the degree of linear correlation between two variables

3.17 specific gas constant

proportional constant in the gas equation of state […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 27 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download JB/T 11798-2014

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
27 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 11798-2014

$395.00