Valid

JB/T 11472-2013Low-speed vehicles - Electrical equipment - Technical specification (English PDF)

低速汽车 电气设备 技术条件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 11472-2013 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

April 25, 2013

Implementation date

September 1, 2013

Scope

JB/T 11472-2013 is the English-translated version of 低速汽车 电气设备 技术条件.

JB/T 11472-2013 is the Chinese standard "Low-speed vehicles - Electrical equipment - Technical specification". Its scope clause reads: This standard specifies the technical requirements, test methods, inspection rules as well as marking, packaging and storage of electrical equipment for low-speed vehicles.

It is applicable to electrical equipment for low-speed vehicles (including motors, electrical and electronic products). Its clauses include technical requirements.

Found what you need?

Document preview — JB/T 11472-2013

National Standard of the People's Republic of China

ICS
65.060

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword i
  • 1 Scope
  • 2 Normative references
  • 3 Technical requirements
  • 4 Test method
  • 5 Inspection rules
  • 6 Marking, packaging and storage

1 Scope

This standard specifies the technical requirements, test methods, inspection rules as well as marking, packaging and storage of electrical equipment for low-speed vehicles.

It is applicable to electrical equipment for low-speed vehicles (including motors, electrical and electronic products).

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 191 Packaging - Pictorial marking for handling of goods

GB/T 2423.1 Environmental testing for electric and electronic products - Part 2: Test methods - Tests A: Cold

GB/T 2423.2 Environmental testing for electric and electronic products - Part 2: Test methods - Tests B: Dry heat

GB/T 2423.3 Environmental testing for electric and electronic products - Part 2: Testing method - Test Cab: Damp heat, steady state

GB/T 2423.4 Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12h+12h cycle)

GB/T 2423.10 Environmental testing for electric and electronic products - Part 2: Test methods - Fc and guidance: Vibration (sinusoidal)

GB/T 2423.17 Environmental testing for electric and electronic products - Part 2: Test methods - Test Ka: Salt mist

GB/T 2423.22 Environmental testing for electric and electronic products - Part 2: Test methods - Test N: Change of temperature

GB/T 2423.34 Environmental testing for electric and electronic products - Part 2: Test methods - Test Z/AD: Composite temperature/humidity cyclic test

GB/T 2828.1 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection

GB/T 4942.1 Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification

GB/T 10069.1 Measurement of the airborne noise emitted by rotating electrical machines and the noise limits - Part 1: Method for the measurement of airborne noise emitted by rotating electrical machines

GB/T 13306 Plates

GB 14048.1 Low-voltage switchgear and controlgear - Part 1: General rules

GB/T 17619 Limits and methods of testing for immunity of electrical/electronic sub-assemblies in vehicles to electromagnetic radiation

GB/T 18655 Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers

JB/T 4159-1999 General technical requirements for electric products in the tropics

QC/T 625 Metallic coatings and conversion coatings for automobile

3 Technical requirements

3.1 General requirements

3.1.1 Basic requirements

Electrical equipment shall meet the requirements of this standard and corresponding product classification standards, and shall be manufactured according to the product drawings and technical documents approved through specified procedures.

3.1.2 Environment conditions

Under the environment conditions specified in Table 1, electrical equipment shall be guaranteed to have rated values.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Normative references

Similar standards

How to Download JB/T 11472-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 11472-2013

$165.00