Valid

JB/T 10854-2019Horizontal continuously cast iron sections (English PDF)

水平连续铸造铸铁型材

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 10854-2019 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

December 24, 2019

Implementation date

October 1, 2020

Scope

JB/T 10854-2019 is the English-translated version of 水平连续铸造铸铁型材.

JB/T 10854-2019 is the Chinese standard "Horizontal continuously cast iron sections".

Its scope clause reads: This standard specifies the classification and designation, technical requirements, test methods, inspection rules, marking and quality certificate, as well as packaging, storage and transportation of horizontal continuous cast gray iron bars and ductile iron bars.

This standard is applicable to cast iron bars with a diameter of phi25 mm to phi400 mm, as well as square, rectangular and special-shaped cross-section bars of corresponding sizes produced by the horizontal continuous casting process (hereinafter referred to as "cast iron bars"). Its clauses include classification and designation.

Found what you need?

Document preview — JB/T 10854-2019

National Standard of the People's Republic of China

ICS
77.140.60
Replacing
JB/T 10854-2008

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword i
  • 1 Scope
  • 2 Normative references
  • 3 Classification and designation
  • 3.1 Classification
  • 3.2 Designation
  • 4 Technical requirements
  • 4.1 Chemical composition
  • 4.2 Mechanical properties
  • 4.3 Metallographic structure
  • 4.4 Surface quality
  • 4.5 Dimensional tolerance
  • 5 Test methods
  • 5.1 Preparation of specimens
  • 5.2 Tensile test
  • 5.3 Hardness test
  • 5.4 Impact test
  • 5.5 Metallographic structure
  • 5.6 Surface quality and dimensional tolerance
  • 6 Inspection rules
  • 6.1 Batch division
  • 6.2 Evaluation and re-inspection of test results
  • 7 Marking and quality certificate
  • 7.1 Marking
  • 7.2 Quality certificate
  • 8 Packaging, storage and transportation
  • 8.1 Packaging and storage
  • 8.2 Transportation

1 Scope

This standard specifies the classification and designation, technical requirements, test methods, inspection rules, marking and quality certificate, as well as packaging, storage and transportation of horizontal continuous cast gray iron bars and ductile iron bars.

This standard is applicable to cast iron bars with a diameter of phi25 mm to phi400 mm, as well as square, rectangular and special-shaped cross-section bars of corresponding sizes produced by the horizontal continuous casting process (hereinafter referred to as "cast iron bars").

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 228.1 Metallic materials - Tensile testing - Part 1: Method of test at room temperature

GB/T 229 Metallic materials - Charpy pendulum impact test method

GB/T 231.1 Metallic materials - Brinell hardness test - Part 1: Test method

GB/T 1348 Spheroidal graphite iron castings

GB/T 5612 Code for representing cast iron

GB/T 7216 Metallographic test for grey cast iron

GB/T 9439 Grey iron castings

GB/T 9441-2009 Metallographic test method for spheroidal graphite cast iron

JB/T 7945.1 Methods for testing the mechanical properties of grey cast iron - Part 1: Tensile testing

3 Classification and designation

3.1 Classification

Cast iron bars are divided into gray iron bars and ductile iron bars according to the morphology of graphite in the metallographic structure.

3.2 Designation

The designation method of cast iron bars shall comply with the provisions of GB/T 5612. Gray iron bars are classified into 5 designations according to the tensile strength of test bars taken from the body of gray iron bars with a diameter of no more than phi30 mm (see Table 1). Ductile iron bars are classified into 8 designations according to the tensile strength and elongation after fracture of test bars taken from the body of ductile iron bars with a diameter of no more than phi60 mm (see Table 1).

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

Editions of JB/T 10854

EditionTitleRevisionStatus
JB/T 10854-2019Horizontal continuously cast iron sectionscurrent editionCurrent
JB/T 10854-2008Horizontal continuously cast iron sectionsprevious editionSuperseded

This page sells the current edition, JB/T 10854-2019. Earlier editions are listed for reference only.

How to Download JB/T 10854-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 10854-2019

$135.00