Valid

JB/T 10063-1999No. 1 standard test block for ultrasonic flaw detection - Technical specifications (English PDF)

超声探伤用1号标准试块 技术条件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 10063-1999 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

April 5, 1999

Implementation date

April 5, 1999

Scope

JB/T 10063-1999 is the English-translated version of 超声探伤用1号标准试块 技术条件.

JB/T 10063-1999 is the Chinese standard "No. 1 standard test block for ultrasonic flaw detection - Technical specifications".

Its scope clause reads: This standard specifies the test methods for ultrasonic test blocks, including the detection of internal defects in the block, the longitudinal wave transit time of the Perspex insert, the deviation in the position of the centre of the R100 arc surface and the deviation of its echo amplitude, and the deviation of the refraction angle scale.

Found what you need?

Document preview — JB/T 10063-1999

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • 3.4.2 Test procedure for internal defects
  • 3.5 Longitudinal wave transit time of the Perspex insert
  • 3.6 Deviation of the R100 arc surface
  • 3.7 Deviation of the refraction angle scale
3.4.2 Test procedure for internal defects

3.4.2.1 Place the probe on the test face of reference block DB-P Z2-2 and move it until the echo from the 2 mm flat-bottomed hole is at its highest; adjust the flaw detector so that the amplitude of the hole echo displayed on the screen is 80 % of the vertical scale.

3.4.2.2 Place the same probe on the front side face of the block under test and, with the instrument set as in 3.4.2.1, find the largest defect inside the body of the block, note the amplitude of its echo and express it as a percentage of the vertical scale.

3.4.2.3 Repeat the method of 3.4.2.2 on the rear side face, the top face and the bottom face of the block under test.

3.5 Longitudinal wave transit time of the Perspex insert

3.5.1 Test equipment: as in 3.4.1 a), b), c) and d), plus reference block No. 1.

3.5.2.1 Place the probe on the 25 mm thickness of reference block No. 1 and adjust the flaw detector so that four back-wall echoes are displayed, with the leading edge of the second back-wall echo at horizontal scale division 5 and that of the fourth at division 10.

3.5.2.2 Place the same probe on the 23 mm thickness of the Perspex under test and, with the instrument set as in 3.5.2.1, measure the position of the leading edge of the first back-wall echo on the horizontal scale. The horizontal distance between that position and scale division 5 represents the difference between the transit time of the longitudinal wave through 23 mm of Perspex and its transit time through 50 mm of grade 20 steel.

3.6 Deviation in the position of the centre of the R100 arc surface and deviation of its echo amplitude

3.6.1 Test equipment: as in 3.4.1 a) and c), plus an angle probe of 2,5 MHz with a refraction angle of 45 degrees and an angle probe of 5 MHz with a refraction angle of 70 degrees, and reference block No. 1.

3.6.2.1 Place the 45 degree angle probe at the centre position of the R100 arc surface of reference block No. 1 and move it back and forth until the echo from the arc surface is at its highest. Using the centre position of the R100 arc surface of block No. 1 as the datum, correct the index point mark of the probe; the corrected index point is denoted O1. With the probe in that position, adjust the flaw detector so that the first echo from the R100 arc surface is 50 % of the vertical scale and note the attenuator reading S1 in decibels.

3.6.2.2 Place the same probe at the centre position of the R100 arc surface of the block under test and move it back and forth until the echo is at its highest; measure the distance a, in millimetres, from the centre position of the R100 arc surface of the block under test. With the probe in that position, adjust the flaw detector so that the first echo is 50 % of the vertical scale and note the attenuator reading S2 in decibels. Where the index point O1 lies in front of the centre position of the R100 arc surface of the block under test, that is on the side away from the centre and towards the arc surface, the deviation is positive and is written +a; otherwise it is written -a. The deviation of the echo amplitude of the R100 arc surface of the block under test relative to that of reference block No. 1 is S2 - S1, in decibels.

3.6.2.3 Repeat the methods of 3.6.2.1 and 3.6.2.2 using the 70 degree angle probe.

3.7 Deviation of the refraction angle scale

3.7.1 Test equipment: as in 3.6.1.

3.7.2.1 Place the 45 degree angle probe at the position marked 45 degrees on the refraction angle scale of reference block No. 1 and move it back and forth until the first echo from the 50 mm hole is at its highest; note the refraction angle scale value corresponding to the index point O1 of the probe.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download JB/T 10063-1999

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 10063-1999

$85.00