HJ 424-2017Technical requirement for environmental labeling products. Digital copying(including multi-function)devices (English PDF)

Foreword

In order to implement the "Environmental Protection Law of the People's Republic of China" and reduce the digital photocopying (including multi-functional) equipment in the process of production and use in the environmental impact, the development of this standard.

This standard digital copy (including multi-functional) equipment product design, production, use, recycling, packaging and description of the proposed Environmental protection requirements.

This standard reference to the German standard basis for environmental labeling Award (Basic Criteria for Award of the Environmental Label) "attached Office Equipment With Printing (Printer, Copier, Multifunction Device) "(Office Equipment With Printing Function (Printers, Copiers, Multi-function Devices)) (RAL-UZ 205,2017), "Technical Requirements for Environmental Labeling Products Word Multifunction Copying Equipment "(HJ/T 424-2008) was revised.

This standard compared with the HJ/T 424-2008 main changes are as follows.

- the name has been modified;

- Removed the definition of energy efficiency;

- Removed battery requirements;

- Removed toner and photoconductor requirements and added cartridge requirements - Added unidentified control indicators and limit values for VOC and fine particulate matter;

- Adjusted product energy efficiency index.

This standard is formulated by the Ministry of Environmental Protection Science and Technology Standards Division.

This standard is mainly drafted by. Environmental Protection Department of Environmental Development Center, the State Office Equipment and Supplies Quality Supervision and Inspection Center.

This standard MEP approved on December 11, this standard since March 1, 2018 into effect.

This standard is interpreted by the MEP.

This standard replaces the standards previously issued as follows.

- HJ/T 424-2008, HJ BZ 40-2000.

Environmental Labeling Product Technical Requirements Digital photocopying (including multifunction) equipment

1 Scope of application

This standard specifies the digital photocopying (including multi-function) equipment (hereinafter referred to as photocopying equipment) environmental labeling products category terms and Definition, basic requirements, technical content and testing methods.

This standard applies to black and white photocopying equipment, color photocopying equipment and to copy as its basic function of digital multi-function photocopying equipment.

2 Normative references

This standard references the following documents in the terms. For undated references, the effective version applies to this standard.

GB 21521 photocopiers, printers and fax machines energy efficiency rating and energy efficiency rating GB/T 13334 copier debug version A3 GB/T 16288 plastic products logo GB/T 18313 Acoustics Information technology Equipment and communication equipment - Measurement of airborne noise GB/T 18455 packaging recycling mark GB/T 21202 digital multi-function monochrome electrostatic copy (print) equipment GB/T 26572 electrical and electronic products limit the requirements of substances GB/T 29793 color copying (including multi-function) equipment HJ 570 Environmental Labeling Product Technical Requirements Toner Cartridge HJ 2512 Environmental Labeling Product Technical Requirements Printers, fax machines and multifunction machines ISO/IEC 28360 Information technology - Office equipment - Determination of chemical emission rates in electronic equipment (Information technology - Office equipment - Determination of chemical emission rates from electronic equipment)

3 Terms and definitions

The following terms and definitions apply to this standard 3.1 digital copying (including multi-function) equipment digital copying (including multi-function) devices by scanning the original image or text into digital signals and digital processing, the electrostatic imaging mode of copying Prepared, multifunctional is the simultaneous inclusion of one or more additional functions (such as printing, telephone, fax, scanning, networking, etc.).

4 Basic requirements

4.1 product quality should be consistent with GB/T 21202 or GB/T 29793 standards.

4.2 The pollutant discharge of the production enterprise shall comply with the discharge standards of pollutants stipulated by the state or local governments.

4.3 product manufacturing enterprises in the production process should be strengthened cleaner production.

5 Technical content

6 Test methods

6.1 Technical content 5.3.2 The test in accordance with the provisions of GB 21521-2014 for the method, the test product should be placed under the provisions of the environmental conditions Set 12h above.

6.2 Technical content 5.3.3 The test in accordance with GB/T 18313-2001 Note 3 in Chapter 7 of the provisions of the method, the test should first meet the Under the conditions.

a) Noise test should be carried out in the factory default conditions, does not involve additional accessories;

b) use GB/T 13334 beta;

c) Test on A4 size paper 70g/m2;

d) If a single product is to be tested, then 3dB (A) should be added to the test result before making a decision. If using 3 products to test, take the average of three product test results to determine.

Note 3. At the time of noise test, at least 6 pages of copying equipment should be made.

6.3 Technical contents 5.3.4 Detection of volatile organic compound (TVOC), benzene, styrene and single substance VOC Sample preparation process Press According to the standard Appendix D of the provisions of the method.

6.4 Technical content 5.3.4 Detection of ozone in the sample preparation process in accordance with the provisions of Appendix E of this standard.

6.5 Technical content 5.3.4 Detection of dust in the sample preparation process according to HJ 2512-2012 Appendix F method.

6.6 Technical Contents 5.3.4 Detection of fine particles in the sample preparation process in accordance with Appendix F of this standard method.

6.7 Other requirements in the technical contents are verified through document examination and on-site inspection.

Appendix A.

(Normative)

Product environmental design requirements no. Requirements object description

1 Various groups of incompatible materials Pieces can be separated or easily separated by auxiliary Partially connected.

Protective parts, base, Electrical and electronic components, Toner cartridge 2 electrical and electronic components and electrical and electronic components easy be found, able to separate.

Equipment as a whole, including Tube 3 to the purpose of the disintegration of recycling, just one Like the tools to complete.

Shell, base, electricity Gas electronic components "General tools" refers to the market can buy to the tool. The terms for "according to have Relevant standards and regulations can only choose a particular company not connected. "

4 Consider the disassembly tools required at design time Focus and space.

Protective parts, base, Electrical and electronic components

5 Can be removed with up to 3 tools for fixing Set screws for components.

Protective parts, base, Electrical and electronic components Tools by type of tool (such as a cross Slot) and size division.

6 a person can complete the disintegration. Machine when the bottom cut angle greater than or equal to 90 degrees, can be at the same time there are multiple sliding in the same direction knot when, must break down more than 3 at the same time Slip into the combination, as does not meet the requirements.

7 no electronic components on the shell. But fixed in the operating part of the housing, as well as the base Functional shell does not apply.

Protective parts -

8 Manufacturers should follow the above order from 1 to 7

Try to disassemble and record the points.

Machine -

Only use plastic parts with similar functions 1 kinds of materials. Reusable parts do not apply.

Over 25g of protection Parts, base, machine Mechanical parts "Similar function" refers to "impact resistance" "Wear resistance" and other functions.

10 Plastic mass more than 25g should be used

Monomer or copolymer.

shell--

No. Requirements object description

11 Mass greater than 25g plastic shell used

The type of monomer or copolymer does not exceed 4 species, and easy to disassemble.

shell--

12 5.1.8 mass greater than 25g, or the largest plane the surface area of more than.200mm2 plastic parts should be in accordance with the requirements of GB/T 16288 standard Show.

Plastic parts -

13 for the product is not easy to peel the label on the shell, Use the same material as the pasting area or Does not affect the recycling of materials.

label--

14 Plastic housing parts are not electroplated. shell--

15 (a) Painting of plastic parts is limited as necessary Minimal (example. manufacturer's name). laser Marking, etc. do not belong to the project mentioned in the "Tu Installed. " Protective parts, drum powder "Painting" includes paint layer, deposited layer and print.

The reused parts do not apply to this clause.

(B) The coating process should be used without prejudice Reuse of paint. Recommended to improve painting operations Labor safety and hygiene personnel conditions and mitigation Environmental load.

Protective parts, drum powder "Paint which does not prevent reuse" means to be coated the loaded parts are compatible with the paint Sex, paint will not hinder the product material again use.

"Improve the labor safety of coating workers Sanitary conditions "refers to the change of coating job site Air ventilation, workers should be protective equipment Wait.

"Reduce the environmental load" means to reduce to large VOC emissions in the gas, equipment processing facilities Set home, painting process layout work hard Use low VOC emissions coatings.

As long as any one of (a) (b) is satisfied.

No. Requirements object description 16 use of renewable materials, protective parts, base, Protection of toner cartridge "Recyclable material" means that it can be used Produce the same recycled material as the original material (Raw material level utilization).

This project examines only the design intent and objectives, Do not examine whether the recycling.

17 Recycled plastics are allowed as raw materials

Part.

Protective parts, base, Toner cartridge "Permitted" refers to the product design requirements, as long as the material is to meet the conditions, you can use. "Part" means that there is a corresponding plastic Material parts (not all parts).

18 Parts and materials in Schedule A.1 are easily removable

under.

Machine -

19 From 15 to 19, the selection of materials was recorded Choose the situation.

Shell, base, drum

Toner

20 In addition to the standard parts, More than 50% of the parts are available to the manufacturer the same generation, the same performance of other products.

Machine -

21 may and may allow the existence of remanufacturing Reprocessed modules or reuse zeroes Machine manufacturers should allow reuse. Its use can be to repair spare parts or the same quality and new products Equivalent to new.

The toner cartridge can be reused Toner cartridge, purely Except containers Refers to the design should not hinder the re-use.

Schedule A.1 should be separated processing of molded products, chemicals and parts * PCB containing capacitors * Use mercury-containing parts for lamps similar to backlighting *battery * Printed circuit board with area over 10cm2 * Toner cartridge, toner, paste, liquid toner (including color separation processing) * Used plastic parts containing bromine flame retardant * LCD screen area over 100cm2 (sometimes fixed on the shell) * External power cord * Contains harmful substances (high > 25mm, diameter > 25mm or volume close to this) Appendix B (Normative) Phthalate Chinese name English abbreviation Diisobutylphthalate DIBP Di- (2-ethylhexy) -phthalate DEHP Butylbenzylphthalate BBP Dibutylphthalate DBP Appendix C (Normative) Polycyclic aromatic hydrocarbons (PAHs) Chinese name English name CAS number Benzo [a] pyrene Benzo [a] pyrene 50-32-8 Acenaphthene 83-32-9 Camphene Acenaphthylene 208-96-8 Anthracene 120-12-7 Benzo [a] anthracene 56-55-3 Benzo [b] fluoranthene 205-99-2 Benzo [g, h, i] perylene (perylene) Benzo [ghi] perylene 191-24-2 Benzo [k] fluoranthene 207-08-9 (1,2-triphenylene) Chrysene 218-01-9 Dibenzo (a, h) anthracene Dibenz [a, h] anthracene 53-70-3 Fluoranthene Fluoranthene 206-44-0 Fluorene Fluorene 86-73-7 Indeno [1,2,3-c, d] pyrene Indeno [1,2,3-cd] pyrene 193-39-5 Naphthalene 91-20-3 Phenanthrene 85-01-8 Pyrene Pyrene 129-00-0 Appendix D (Informative) TVOC, Benzene, Styrene and Unidentified VOC Emission Rate Sample Preparation Process D.1 Foreword this appendix describes the emission rates of TVOC, benzene, styrene and unidentified VOCs as defined in Test Method 6.3 Kind of process.

D.2 General Provisions D.2.1 The test is carried out in the specified test chamber (D.3.1).

D.2.2 The test using the standard configuration of the product, non-standard configuration does not participate in the test.

D.3 Test conditions

D.3.1 Test Chamber Regulations Test chamber should meet the following conditions.

a) Temperature. 23 °C ± 2 °C;

b) Relative humidity Note D1. 50% ± 5%;

c) air exchange rate. Chamber volume <= 5m3. (1 <= n <= 5) ± 5%;

Chamber volume > 5m3. (1 <= n <= 2) ± 5%;

Note D1. If necessary, in order to prevent the equipment from printing due to moisture emitted from the paper leading to increased air humidity and affect the test results in the preparation phase After the end, if the chamber volume > 5m3, the air exchange rate can be adjusted to n = 1-2h-1; if the chamber volume <= 5m3, the air exchange rate can be adjusted to n = 1-5h-1, if necessary, the relative humidity can be reduced to below 10%, the air flow becomes dry, in order to maintain the print phase chamber air humidity below the critical Value (<=85%).

d) Chamber flow rate. 0.1 m/s ~ 0.3 m/s;

e) Volume of test sample to chamber volume Note D2. 0.0025 5m3);

c) According to the product category using the provisions of the test version of the original for printing, should work continuously for 10min Note D5, note D6 above;

Note D5. For equipment that does not complete at least 5 minutes of print time and does not have a large capacity output tray for design reasons, the test should be done in duplex mode (double Surface printing), the device under test should be the default setting (standard print quality).

Note D6. During the test, the power meter should be used to monitor the operating status of the product.

d) continue sampling until the air exchange is completed. After sampling, immediately sealed at both ends of the sampling tube;

e) Use a spectrophotometer to test the color value of the black and white print or the color value L, a, b of the color print and record.

D.4.4 Sample Analysis the samples were analyzed with a thermal analyzer + gas chromatography-mass spectrometer (GCMS).

D.5 Calculation of the result D.5.1 Calculation of TVOC emission rates D.5.1.1 chamb...