HJ 2504-2011Technical requirement for environmental labeling products. Camera (English PDF)

5.1 Product Design Requirements

5.1.1 The product adopts a detachable design.

5.1.2 Optical lenses used in the product shall not use lead (Pb) and its compounds as formula ingredients.

5.1.3 Plastic parts requirements

5.1.3.1 The content of vinyl chloride monomer in the outer shell of the product shall not exceed 1 mg/kg; the phthalates listed in Appendix A shall not be used as A plasticizer in which no more than four types of polymers, copolymers or polymerization mixtures are used and should be easily decomposed.

5.1.3.2 Plastic parts with a mass exceeding 25 g and a surface area exceeding.200 mm2 shall be in accordance with the requirements of GB/T 16288.

mark.

5.1.3.3 Decabromodiphenyl ether (DBDPO), short-chained chlorinated paraffins (SCCPs) shall not be used.

5.2 Battery requirements

5.2.1 After charging and discharging 300 times as a power source, the remaining capacity of the lithium ion rechargeable battery should be greater than 80% of its rated capacity.

5.2.2 The limit of heavy metals in the single-cell lithium-ion rechargeable battery as the power supply shall meet the requirements of Table 1.

Table 1 Limited units of heavy metals in batteries. mg/kg

Project Lead (Pb) Cadmium (Cd) Mercury (Hg) Single power battery <=40 <=20 <=5

5.3 Limitation requirements for hazardous substances in products

Lead (Pb), cadmium (Cd), mercury (Hg), hexavalent chromium (Cr6), polybrominated biphenyls (PBBs) and polybrominated diphenyls in products and product components the limits for six hazardous substances (PBDEs) should meet the requirements of SJ/T 11363, with the following exceptions.

a) The case where lead is used in ceramics of electronic ceramic parts.

b) When lead is applied as an alloy component to a steel alloy and its content (mass fraction) is <=0.35%.

c) When lead is used as an alloy component in an aluminum alloy, and its content (mass fraction) is <=0.4%.

d) When lead is used as a component of an alloy in a copper alloy and its content (mass fraction) is <= 0.4%.

e) Lead is used as a soldering alloy for microprocessor pins and package connections, and its content (mass fraction) is 80% to 85%.

f) The case where lead is used in the operation of a solder alloy for connection in a flip-chip package of an integrated circuit.

g) The case where lead is used in the glass of an LCD flat fluorescent lamp.

5.4 Production process requirements

5.4.1 Methylene chloride (CH2Cl2) should not be used as a cleaning solvent in the production of optical lenses.

5.4.2 Lead-free soldering process should be used during assembly and connection of product parts.

5.4.3 Hydrochlorofluorocarbons (HCFCs), 1,1,1-trichloroethane (C2H3Cl3), trichloroethylene (C2HCl3), dichloroethane should not be used.

(CH3CHCl2), chloroform (CHCl3), bromopropane (C3H7Br), n-hexane (C6H14), toluene (C7H8), xylene [C6H4(CH3)2] the substance is used as a cleaning solvent.

5.5 Product packaging materials

5.5.1 The content of vinyl chloride monomer shall not exceed 1 mg/kg.

5.5.2 Hydrochlorofluorocarbons (HCFCs) should not be used as blowing agents.

5.5.3 The marking shall be carried out in accordance with the requirements of GB/T 18455.

5.6 Product recycling and utilization

Enterprises should establish waste product recycling and recycling treatment systems to provide information on product recycling and recycling.

5.7 Product disclosure information requirements

Public information should include the following.

a) Product power saving mode, standby mode description;

b) recommendations for the recycling and disposal of the battery used in the product;

c) Product recycling information and corresponding channels.