HG/T 3880-2006Pressure and vacuum resistant rubber-covered rotary shaft lip seals with internal reinforcement (English PDF)
耐正负压内包骨架旋转轴 唇形密封圈
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for HG/T 3880-2006 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
July 26, 2006
Implementation date
March 1, 2007
Scope
HG/T 3880-2006 is the English-translated version of 耐正负压内包骨架旋转轴 唇形密封圈.
HG/T 3880-2006 is a recommended chemical industry standard of China for rubber-covered rotary shaft lip seals with internal reinforcement that must withstand both pressure and vacuum.
It gives the terminology, definitions and symbols for these seals, sets their types and requirements, and covers the test methods together with marking, packaging, transport and storage.
It applies to seals mounted on the rotating shafts of gear pumps to retain hydraulic oil and grease, working between -40 °C and 100 °C and at pressures from -56 kPa to 0.2 MPa.
Classified G43 with the international groups 83.140.50 and 23.100.60, it quotes GB/T 528-1998, GB/T 531-1999, GB/T 1682-1994, GB/T 3512-2001, GB/T 5721-1993, GB/T 9877.1-1988, GB/T 15326-1994 and JB/T 7042-1993. Issued on 26 July 2006, it has applied since 1 March 2007.
Found what you need?
Document preview — HG/T 3880-2006
National Standard of the People's Republic of China
- ICS
- 83.140.50
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- [Preview only]
- 1 Scope
- 2 Normative References
- 3 Terms and definitions
- 3.1 Category A
- 3.2 Category B
- 4 Classification and designation
- 4.1 General
- 4.2 Character group 1
- 4.3 Character group 2
- 4.4 Character group 3
- 4.5 Character group 4
- 4.6 Designation example
- 5 Test Methods
- 5.1 Appearance requirements
- 5.2 Technical requirements
- 5.3 Environmental requirements
- 6.1 Test conditions
- 6.2 Test substrate
- 6.3 Apparatus
- 6.4 Appearance
- 6.5 Coating property
- 6.6 Shear elongation
- 6.7 Tensile shear strength
- 6.8 Tensile bond strength
- 6.9 Free formaldehyde
- 7 Inspection rules
- 7.1 Inspection
- 7.2 Batching
- 7.3 Sampling
- 7.4 Judgment of inspection results
- 8 Marking, packaging, transportation and storage
- 8.1 Marking
- 8.2 Packaging
- 8.3 Transportation
- 8.4 Storage
- 9 Packaging, transportation and storage
1 Foreword
HG/T 3880-2006 was issued by Ministry of Industry and Information Technology of the People's Republic of China on 26 July 2006 and has been in force since 1 March 2007.
The HG/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.
The document runs to 15 pages in English translation.
2 Scope Preview
This standard is a recommended chemical industry standard of China for rubber-covered rotary shaft lip seals with internal reinforcement that must withstand both pressure and vacuum. It gives the terminology, definitions and symbols for these seals, sets their types and requirements, and covers the test methods together with marking, packaging, transport and storage. It applies to seals mounted on the rotating shafts of gear pumps to retain hydraulic oil and grease, working between -40 °C and 100 °C and at pressures from -56 kPa to 0.2 MPa. Classified G43 with the international groups 83.140.50 and 23.100.60, it quotes GB/T 528-1998, GB/T 531-1999, GB/T 1682-1994, GB/T 3512-2001, GB/T 5721-1993, GB/T 9877.1-1988, GB/T 15326-1994 and JB/T 7042-1993.
HG/T 3880-2006 falls under ICS 83.140.50, in the field of rubber and plastics industries.
This catalogue holds 313 other HG/T standards in that field.
In this catalogue, HG/T standards carry edition years from 1975 to 2026.
3 Normative references
GB/T 528-1998 — Rubber, vulcanized or thermoplastic--Determination of tensile stress-strain properties [including MODIFICATION 1]
GB/T 531-1999 — Rubber--Determination of indentation hardness by means of pocket hardness meters
GB/T 1682-1994 — Rubber, vulcanized--Determination of low-temperature brittleness (single test piece method)
GB/T 1690-1992 — Rubber, vulcanized-Determination of the effect of liquids
GB/T 3512-2001 — Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests - Air-oven method
GB/T 5719
GB/T 5721-1993 — General rules of identification, packaging, transportation and storage for rubber sealing products
GB/T 7759-1996 — Rubber, Vulcanized or thermoplastic--Determination of compression set at ambient elevated or low temperatures
GB/T 9877.1-1988 — Hydraulic fluid power -- Guide specifications for designing rotary shaft lip type seals
GB/T 14273-1993 — Rotary shaft lip type seals-Performance test proceduces
GB/T 15326-1994 — Appearance quality for rotary shaft lip seals
JB/T 7042-1993(2005)
4 About this standard
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
English translation: about 15 pages
5 Related standards
Standards on related subjects:
GB/T 3672.1-2025 — Tolerances for rubber products - Part 1: Dimensional tolerances
HG/T 4622-2014 — Rubber compounds for seals used for dimethyl ether
GB/T 5721-1993 — General rules of identification, packaging, transportation and storage for rubber sealing products
HG/T 6183-2023 — Ductile iron pipe interface anti-slip and anti-loosening rubber sealing ring
HG/T 6181-2023 — Rubber gaskets for engine oil pans
HG/T 4116-2023 — Rubber gaskets for drum washing machine viewing windows
6 Classification and status
International classification (ICS): 83.140.50
Chinese Standard Classification (CCS): G 43
Prefix HG/T: recommended standard.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 528-1998Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties
- GB/T 531-1999Rubber--Determination of indentation hardness by means of pocket hardness meters
- GB/T 1682-1994Vulcanized rubber - Determination of low-temperature brittleness - Single test piece method
- GB/T 1690-1992Rubber, vulcanized or thermoplastic—Determination of the effect of liquids
- GB/T 3512-2001Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests in hot air
- GB/T 5719Rubber sealing articles - Vocabulary
Similar standards
How to Download HG/T 3880-2006
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 14273-1993 — Rotary shaft lip type seals-Performance test proceduces
GB/T 15326-1994 — Appearance quality for rotary shaft lip seals
GB/T 1682-1994 — Rubber, vulcanized--Determination of low-temperature brittleness (single test piece method)
HG/T 3880-2006
$85.00