Valid

HG/T 2871-2022Test method for flex resistance of whole rubber footwear (English PDF)

胶鞋整鞋屈挠试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for HG/T 2871-2022 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

September 30, 2022

Implementation date

April 1, 2023

Scope

HG/T 2871-2022 is the English-translated version of 胶鞋整鞋屈挠试验方法.

HG/T 2871-2022 is the Chinese standard "Test method for flex resistance of whole rubber footwear".

Its scope clause reads: This document provides the test methods for determining whether there are abnormal conditions, such as degumming and cracks between uppers, soles and foxing strips after repeated flex resistance tests on the whole rubber shoes under specified test conditions.

This document gives two methods: Method A and Method B. This document is applicable to tests for flex resistance of whole rubber shoes. The test method may be used as a reference for other types of shoes. Its clauses include terms and definitions; principle; apparatus.

Found what you need?

Document preview — HG/T 2871-2022

National Standard of the People's Republic of China

Replacing
HG/T 2871-2008

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword i
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Principle
  • 5 Apparatus
  • 6 Specimen conditioning and test atmosphere
  • 7 Test conditions
  • 8 Test procedures
  • 9 Test results
  • 10 Test report
  • Annex A (Informative) Determination of flexing line in Method B

1 Scope

This document provides the test methods for determining whether there are abnormal conditions, such as degumming and cracks between uppers, soles and foxing strips after repeated flex resistance tests on the whole rubber shoes under specified test conditions. This document gives two methods: Method A and Method B.

This document is applicable to tests for flex resistance of whole rubber shoes. The test method may be used as a reference for other types of shoes.

2 Normative references

The following documents contain provisions which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 2941 Rubber - General procedures for preparing and conditioning test pieces for physical test methods

3 Terms and definitions

No terms and definitions are listed in this document.

4 Principle

While being flexed repeatedly, rubber shoes will be subjected to stress-induced deformation and material fatigue under the action of repeated tensile stress. In this case, degumming will occur between the upper and the foxing strip, between the upper and the outsole, and between the sole and the foxing strip; cracks (gaps) or fracture will occur on the upper, sole, and foxing strip. This test method is based on this principle above. In the test, take a whole rubber shoe assembled with a suitable bendable last or pressing block, and then place it on the shoe flexing tester, and carry out the flex resistance test for a specified times at the specified angle and frequency. Then measure the length of the crack (gap) on the sole of the rubber shoe and the degumming length between the foxing strip and the upper or between the upper and the outsole, and observe whether there are cracks, ruptures, or other abnormalities present on the upper, sole, and foxing strip.

5 Apparatus

5.1 Vernier caliper

Vernier caliper with a division value of 0.02 mm.

5.2 Inner length gauge

Inner length gauge with a division value of 1.0 mm.

5.3 Retractable tape measure

Retractable tape measure with a division value of 1.0 mm.

5.4

Folding resistance test instrument for Method A

5.4.1

The flexing angle is adjustable and falls in the range of 35° to 60°.

5.4.2

The flexing frequency is adjustable and falls in the range of 50 times/min to 300 times/min.

5.4.3

The function of automatic shutdown according to the preset number of flexing times is available.

5.4.4 A blowing device shall be provided to dissipate heat from the flexing portion of a specimen.

5.4.5 Bendable last

The bendable last is equipped with a steel shaft of phi (5.5±0.5) mm × (40.0±2.0) mm on the vertical line from the first metatarsophalangeal joint to the axis of the last bottom; the maximum bending angle is not less than 60°. After the steel shaft is installed, the surface of the last bottom shall not be concave or convex.

5.5 Folding resistance test instrument for Method B

5.5.1

The flexing angle is adjustable and falls in the range of 0° to 90°.

5.5.2

The flexing frequency is adjustable and falls in the range of 50 times/min to 180 times/min.

5.5.3

The function of automatic shutdown according to the preset number of flexing times is available.

5.5.4 Pressing block

It is installed at the front sole area of the specimen for fixation. Its specifications are shown in Table 1 and Figure 1. It is made of rubber with a Shore A hardness greater than 75.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

Editions of HG/T 2871

EditionTitleRevisionStatus
HG/T 2871-2022Test method for flex resistance of whole rubber footwearcurrent editionCurrent
HG/T 2871-2008Test method for flex resistance of whole rubber footwearprevious editionSuperseded

This page sells the current edition, HG/T 2871-2022. Earlier editions are listed for reference only.

How to Download HG/T 2871-2022

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

HG/T 2871-2022

$120.00