GB/Z 44235-2024Nanotechnologies - Characteristics and measurement methods of air filter media containing polymeric nanofibers (English PDF)
纳米技术 含聚合物纳米纤维的空气过滤介质特性及测量方法
This is a limited preview
Buy now to download the full PDF (23 pages)
Need quotation for your management?
Get a formal quotation for GB/Z 44235-2024 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
August 23, 2024
Implementation date
August 23, 2024
Scope
GB/Z 44235-2024 is the English-translated version of 纳米技术 含聚合物纳米纤维的空气过滤介质特性及测量方法.
GB/Z 44235-2024 is a guidance document, not a mandatory standard, that lists the characteristics to be measured for air filter media whose surface carries a layer of polymeric nanofibers, and describes the measurement method for each one.
Adopted identically from ISO/TS 21237:2020, it separates basic from optional characteristics and covers fiber diameter, morphology, specific surface area, chemical composition, thermal stability, crystal structure, crystallinity and grain size, together with the content of the report.
Informative annexes show the typical structure of nanofiber filter media and give report formats for basic and optional characteristics. Clause 1 excludes health and safety related characteristics, and notes that pressure drop and particle removal efficiency are judged with application-specific test methods from other standards. It was issued on 23 August 2024.
Found what you need?
Document preview — GB/Z 44235-2024
National Standard of the People's Republic of China
- ICS
- 07.120
- Classification
- L 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Abbreviations
- 5 Characteristics to be measured and their measurement methods
- 5.1 Overview
- 5.2 Basic characteristics and optional characteristics and their measurement methods
- 5.3 Description of characteristics and their measurement methods
- 5.3.1 Overview
- 5.3.2 Fiber diameter
- 5.3.3 Morphology
- 5.3.4 Specific surface area
- 5.3.5 Chemical composition
- 5.3.6 Thermal stability
- 5.3.7 Crystal structure
- 5.3.8 Crystallinity
- 5.3.9 Grain size
- 6 Report
- Appendix A (Informative) Typical Structure of Nanofiber Air Filter Media
- Appendix B (Informative) Test report format for basic characteristics
- Appendix C (Informative) Test report format for optional characteristics
- References
Foreword
This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1: Structure and drafting rules for standardization documents" Drafting is required.
This document is equivalent to ISO /TS 21237-2020 "Nanotechnology-based air filter media properties and performance of polymer nanofibers" The document type of "Specification for Measurement Methods" was adjusted from ISO technical specifications to my country's national standardization guiding technical documents.
The following minimal editorial changes were made to this document.
--To coordinate with the existing standard, the name of the standard is changed to "Nanotechnology-based Air Filter Media Characteristics Containing Polymer Nanofibers" and measurement methods.
Introduction
Air filter media plays an important role in the performance and efficiency of different types of air filters. Most air filter media utilizes nonwoven The material separates solid or liquid particles. Air filter media are widely used, such as gas turbine air intake, industrial dust removal, respiratory masks, personal Protective equipment, heating, ventilation and air conditioning systems, clean rooms, etc.
In recent years, air filter media containing nanofibers have been widely used due to their high filtration efficiency and low pressure drop characteristics brought about by the slip flow effect (see Reference [5]), has been commercialized and widely used in different industries. Air filter media containing nanofibers are usually prepared by spinning The nanofibers are directly deposited on the surface of a suitable porous substrate.
Since the diameter of nanofibers is significantly smaller than that of conventional microfibers used in filters, the probability of inertial collision and interception can be increased.
At the same time, slip flow can also reduce pressure drop, allowing more pollutants to flow through the nanofiber surface, thus It can also improve inertial collision and interception efficiency. Under the same pressure drop, the filtration capacity of the nanofiber layer is better than that of the traditional fiber layer.
In addition, the high specific surface area of nanofibers helps to absorb pollutants from the air. These advantages make air filter media containing nanofibers Widely used in air filtration (see references [5][6][7]).
Air filter media containing nanofibers can be manufactured by different techniques such as electrospinning and centrifugal spinning.
The crystal structure, morphology and diameter of the fibers are different, and they are deposited on the surface of the substrate to form a mesh nonwoven layer. The specific surface area of the nonwoven layer and the pores of the interpenetrating fibers The porosity is mainly affected by the diameter and morphology of nanofibers.
Polyester (PU) and other polymer nanofibers are commonly used in air filtration media. Nanofibers can be deposited on different types of textiles or Appendix A shows a schematic cross-sectional view of an air filter medium containing nanofibers (see Figure A.1) and its typical structure, shape, and SEM images of morphology and texture (see Figures A.2 and A.3).
This document helps to facilitate communication between suppliers and buyers and supports the growing trade in this new type of air filtration media.
1 Scope
This document specifies the properties that should be measured for air filter media containing polymer nanofibers on the substrate surface and describes the corresponding measurement methods.
This document does not address health and safety related characteristics.
Note: Use relevant published standards to evaluate the application-related properties/performance of air filtration media. Use test methods appropriate to the specific application.
Measure the physical properties and performance of filter media such as pressure drop and particle removal efficiency.
2 Normative references
This document has no normative references.
3 Terms and definitions
The following terms and definitions apply to this document.
3.1 Air filter
A device for separating solid or liquid particles (3.6) or gaseous pollutants from a passing gas stream.
NOTE 1 The device is typically composed of one or more layers of porous, fibrous or granular material.
Note 2.Air filters specifically refer to the use of filtering to purify the air flowing through them, while air purifiers do not limit their specific methods of reducing air pollution.
[Source: ISO 29464:2017, 3.1.16, modified]
3.2 Air filter medium
Permeable porous material used during filtration (3.3) to capture or deposit the filtrate
NOTE: The filter medium consists of a nanofiber (3.5) layer and a substrate (3.7).
[Source: GB/T 18690.1-2009, 2.27, modified]
3.3 Filtration
The activity of separating suspended contaminants from a fluid by retaining them (also includes the construction and commissioning of filtration equipment). activities involved in the placement).
[Source: ISO 29464:2017, 3.5.29]
3.4 Nanoscale
The length range is approximately between 1 nm and 100 nm.
[Source: ISO 80004-1:2023, 3.1.1]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 23 pages — is available in the English PDF.
Similar standards
How to Download GB/Z 44235-2024
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/Z 102.17-2026 — Semiconductor devices - Discrete devices - Part 17: Magnetic and capacitive coupler for basic and reinforced insulation
GB/Z 103-2026 — Health informatics - The architecture of internet healthcare service network
GB/Z 108-2026 — Health informatics - Internet healthcare service pattern
GB/Z 44235-2024
$300.00