GB/Z 34447-2017Sharp edge testing apparatus and test procedure for lighting equipment -- Tests for sharpness of edge (English PDF)
照明设备的锐边试验装置和试验程序 锐边试验
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/Z 34447-2017 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Level / Type
National · Recommended
Issue date
October 14, 2017
Implementation date
May 1, 2018
Scope
GB/Z 34447-2017 is the English-translated version of 照明设备的锐边试验装置和试验程序 锐边试验.
GB/Z 34447-2017 — This Guidance Document describes in detail a test device and test procedure for photographs that may be accessible to users or installers Hazard sharp edge on equipment for risk assessment.
Found what you need?
Document preview — GB/Z 34447-2017
National Standard of the People's Republic of China
- ICS
- 29.140.40
- Classification
- K 73
Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Contents
- Foreword
- 1 Scope
- 2 test equipment
- 3 calibration
- 4 test head preparation
Foreword
This Guidance Document is drafted in accordance with the rules given in GB/T 1.1-2009 and GB/T 20000.2-2009.
This Guidance Document uses the translation method equivalent to IEC TR62854.2014 "Sharp Edge Testing Equipment and Test Procedures for Lighting Equipment
Ordered sharp edge test. "
This Guidance Document is proposed by China National Light Industry Council.
The guidance of technical documents by the National Standardization Technical Committee Lighting Lighting Technical Committee (SAC/TC224/SC2)
Focused.
The drafting of the guidance of technical documents. Shanghai Times Lighting Appliance Co., Ltd. test, the National Lighting Quality Supervision and Inspection Center,
National Light Source Quality Supervision and Inspection Center (Shanghai).
1 Scope
This Guidance Document describes in detail a test device and test procedure for photographs that may be accessible to users or installers
Hazard sharp edge on equipment for risk assessment.
2 test equipment
Sharp edge tester --- Equipment mainly includes a handle with arm, a fixed to the handle, the stability of the arm to exert a constant force Zhang
Spring force. The arm is a piece of cylindrical steel located at the end of the adjustable arm, with an outer diameter of 12.7 mm and a length of 19 mm. Swing arm to be wrapped with three test
Tape inspection, the outer two as a sensing zone, the inner as an indicator zone. Alternatively, the above three test strips are wrapped around a maximum diameter of 15.9 mm
Remove the sleeve, while the sleeve is set on the diameter of 12.7mm steel head. See Figure 1 or Figure 2.
Indicator band (inner) --- 19.1mm wide, one side (back) with an adhesive coating, with the characteristics of Table 1 black vinyl foam tape.
Sensing tape No. 2 (middle layer) - white vinyl foam tape with 19.1 mm wide, double-sided adhesive coating and having the characteristics of Table 1.
No. 1 sensing tape (outer) --- 19.1mm wide, single-sided adhesive coating, with the characteristics of Table 1 natural color PTFE tape. thin
Tetrafluoroethylene backing (film) is a thin layer cut from the cylindrical block material.
Calibration equipment --- a can be applied (6.672 +/- 0.133) N weight (mass) and a line.
3 calibration
The sharp edge tester should be calibrated to have a force of (6.7 +/- 0.133) N applied to the center of the test head when the arm is between stops. Arm length adjustable
To complete the calibration. For special evaluation, the force can be adjusted to different values.
A typical calibration procedure for adjusting arm length during calibration is shown in Figure 3.
Loosen the adjustment screw that fixes the boom on the main drum.
When the handle is firmly held in the horizontal position, the calibration weight is hung in the center of the boom head.
Adjust the length of the inner boom of the main drum so that the boom that receives the weight of the loaded weight remains in a horizontal position.
Tighten the adjusting screw to lock the rotating arm firmly in the main drum.
Recheck the calibration and remove the weight.
4 test head preparation
The surface of the test head shall be coated with three layers of test tape in the following order.
a) The first layer (inner layer) --- indicating tape, as shown in Table 1, black vinyl foam tape.
b) Second layer (middle layer) --- No. 2 sensing tape, as shown in Table 1, white vinyl foam tape.
c) Third layer (outer layer) --- No. 1 sensing tape, as shown in Table 1 tetrafluoroethylene tape.
In order to prevent the test strip is stretched, each test strip should be wrapped around the circumference of the test head about 180 °. When fixed to the test head, the test tape is not
To be stretched. See Figure 4.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
How to Download GB/Z 34447-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/Z 102.17-2026 — Semiconductor devices - Discrete devices - Part 17: Magnetic and capacitive coupler for basic and reinforced insulation
GB/Z 103-2026 — Health informatics - The architecture of internet healthcare service network
GB/Z 108-2026 — Health informatics - Internet healthcare service pattern
GB/Z 34447-2017
$115.00