GB/T 7095.7-2008Enamelled rectangular copper winding wires - Part 7:Polyester enamelled rectangular copper wire, class 130 (English PDF)
漆包铜扁绕组线 第7部分：130级聚酯漆包铜扁线
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 7095.7-2008 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 13, 2008
Implementation date
March 1, 2009
Scope
GB/T 7095.7-2008 is the English-translated version of 漆包铜扁绕组线 第7部分：130级聚酯漆包铜扁线.
GB/T 7095.7-2008 is the Chinese standard "Enamelled rectangular copper winding wires - Part 7:Polyester enamelled rectangular copper wire, class 130". Its scope clause reads: GB/T 7095 provisions of this part of the 130 to polyethylene terephthalate resin-based single coat enamelled copper flat wire winding Claim.
Corresponding to the temperature index temperature in Celsius is not recommended wire temperature, because it depends on the type of device in use include Many factors within.
This section applies to a conductor nominal size range. --- Broadside size. minimum 2.00mm, maximum 16.00mm; --- Narrow size. minimum 0.80mm, maximum 5.60mm. This section includes Level 1 and Level 2 film thickness enamelled copper flat wire, and is applicable to all specifications conductor.
A combination of size and narrow size broadside and wide/narrow ratio see GB/T 7095.1-2008. Its clauses include definitions, test methods and general appearance; dimensions; resistance; elongation; spring angle.
Found what you need?
Document preview — GB/T 7095.7-2008
National Standard of the People's Republic of China
- ICS
- 29.060.10
- Classification
- K 12
- Replacing
- GB/T 7095.7-1995
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Definitions, test methods and appearance General
- 5 Resistance
- 7 spring angle
- 8 flexibility and adhesion
- 9 Thermal Shock
- 10 Softening
- 11 scratch
- 12 Solvent
- 13 Breakdown Voltage
- 14 Insulation Continuity
- 15 Temperature index
- 16 anti-freezing agent
- 17 2 weldability
- 18 heat or solvent bonding
- 19 2 dielectric loss factor
- 20 transformer oil resistant
- 21 3 Loss
- 23 pinhole test
- 30 3 Packaging
1 Scope
GB/T 7095 provisions of this part of the 130 to polyethylene terephthalate resin-based single coat enamelled copper flat wire winding
Claim.
Corresponding to the temperature index temperature in Celsius is not recommended wire temperature, because it depends on the type of device in use include
Many factors within.
This section applies to a conductor nominal size range.
--- Broadside size. minimum 2.00mm, maximum 16.00mm;
--- Narrow size. minimum 0.80mm, maximum 5.60mm.
This section includes Level 1 and Level 2 film thickness enamelled copper flat wire, and is applicable to all specifications conductor.
A combination of size and narrow size broadside and wide/narrow ratio see GB/T 7095.1-2008.
2 Normative references
The following documents contain provisions which, through GB/T reference in this 7095 constitute provisions of this part. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB/T 7095.1-2008 flat enamelled copper winding wires - Part 1. General requirements (IEC 60317-0-2.2005, IDT)
3 Definitions, test methods and General Appearance
3.1 General definitions and test methods
General definitions and test methods see GB/T 7095.1-2008 Chapter 3.
If GB/T 7095.1-2008 in this section are contradictory to this section shall prevail.
3.2 Appearance
See GB/T 7095.1-2008 in Chapter 3.
4 Dimensions
See GB/T 7095.1-2008 in Chapter 4.
5 resistance
See GB/T 7095.1-2008 in Chapter 5.
6 Elongation
See GB/T 7095.1-2008 in Chapter 6.
7 spring angle
See GB/T 7095.1-2008 in Chapter 7.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 7095.7
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 7095.7-2008 | Enamelled rectangular copper winding wires - Part 7:Polyester enamelled rectangular copper wire, class 130 | current edition | Current |
| GB/T 7095.7-1995 | Enamelled rectangular copper winding wires - Part 7:Polyester enamelled rectangular copper wire, class 130 | previous edition | Superseded |
This page sells the current edition, GB/T 7095.7-2008. Earlier editions are listed for reference only.
How to Download GB/T 7095.7-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 7095.6-2008 — Enamelled rectangular copper winding wires -- Part 6: Polyester or polyesterimide overcoated with polyamide-imide enamelled rectangular copper wire, class 200
GB/T 7095.5-2008 — Enamelled rectangular copper winding wires -- Part 5: Aromatic polyimide enamelled rectangular copper wire, class 240
GB/T 7095.4-2008 — Enamelled rectangular copper winding wires -- Part 4: Polyesterimide enamelled rectangular copper wire, class 180
Secure payment via Stripe
Payments accepted
GB/T 7095.7-2008
$15.00