GB/T 5013.7-2008Rubber insulated cables of rated voltages up to and including 450/750 V -- Part 7: Heat resistant ethylene-vinyl acetate rubber insulated cables (English PDF)
额定电压450/750V及以下橡皮绝缘电缆 第7部分:耐热乙烯-乙酸乙烯酯橡皮绝缘电缆
This is a limited preview
Buy now to download the full PDF (3 pages)
Need quotation for your management?
Get a formal quotation for GB/T 5013.7-2008 in 30 minutes.
Issued by
Standardization Administration of China
Level / Type
National · Recommended
Issue date
January 22, 2008
Implementation date
September 1, 2008
Scope
GB/T 5013.7-2008 is the English-translated version of 额定电压450/750V及以下橡皮绝缘电缆 第7部分:耐热乙烯-乙酸乙烯酯橡皮绝缘电缆.
GB/T 5013.7-2008 — This section GB/T 5013 gives a rated voltage of 450/750V and below, ethylene - vinyl acetate rubber insulated cable technology Claim. Each cable shall comply with the requirements and the specific requirements of this part of GB/T 5013.1 regulations.
Found what you need?
Document preview — GB/T 5013.7-2008
National Standard of the People's Republic of China
- ICS
- 29.060.20
- Classification
- K 13
- Replacing
- GB 5013.7-1997
Issued by: Standardization Administration of China
Contents
- Foreword
- 1 Overview
- 1.1 Scope
- 1.2 Normative references
- 2.1 Model
- 2.2 Rated voltage
- 2.3 Structure
Foreword
GB/T 5013 "rated voltage 450/750V and below rubber insulated cable" is divided into eight sections.
--- Part 1. General requirements;
--- Part 2. Test methods;
--- Part 3. Heat resistant silicone rubber insulated cables;
--- Part 4. Cords and flexible cables;
--- Part 5. Lift cables;
--- Part 6. Arc welding cables;
--- Part 7. Heat resistant ethylene - vinyl acetate rubber insulated cables;
--- Part 8. Cords.
This section GB/T 5013 Part 7. This section identical with IEC 60245-7:1994 "rated voltage 450/750V and with Under rubber insulated cables Part 7. Heat resistant ethylene - vinyl acetate rubber insulated cables "(in English) and its amendments Amendment1.
1997 (in English).
For ease of use, GB/T 5013 made this part of the following editorial changes.
"." --- With a decimal point instead of a comma as the decimal point, "";
--- Delete international standards foreword.
This part of IEC original 2.3.4 and 3.3.4 corresponding editorial errors were corrected.
This section from the implementation date instead of GB 5013.7-1997.
This section of the main changes compared to GB 5013.7-1997 are as follows.
--- Table 1 and Table 3, increased the average outer diameter of the lower limit, the average outer diameter of the cap and modify the value.
This part is proposed by the China Electrical Equipment Industrial Association.
This part of the National Standardization Technical Committee of wire and cable.
This part of the unit responsible for drafting. Shanghai Electric Cable Research Institute.
Participated in the drafting of this section. Jiangsu Shangshang Cable Group, Kunming Cable Co., Ltd., Qingdao Hanlan Group Co., Ltd., Hainan Yang Cable Co., Ltd., Tianjin Jinshan Electric Wire & Cable Co., Ltd., Wuxi Jiangnan Cable Co., Ltd.
1 Overview
1.1 Scope
This section GB/T 5013 gives a rated voltage of 450/750V and below, ethylene - vinyl acetate rubber insulated cable technology Claim.
Each cable shall comply with the requirements and the specific requirements of this part of GB/T 5013.1 regulations.
1.2 Normative references
The following documents contain provisions which, through GB/T reference in this 5013 constitute provisions of this section. For dated reference documents Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB/T 2951.1-1997 cable insulation and sheathing materials test methods - Part 1. General Test Methods 1. Thick Degree and dimensions measuring --- mechanical tests (idt IEC 60811-1-1:1993) GB/T 2951.2-1997 cable insulation and sheathing materials test methods - Part 1. General test methods - Part 2. Hot Aging methods (idt IEC 60811-1-2. 1985) GB/T 2951.5-1997 cable insulation and sheathing materials test methods - Part 2. elastomeric compounds specific test side Act 1. Ozone resistance test --- --- Hot set test - Mineral oil immersion test (idt IEC 60811-2-1. 1986) GB/T 2951.6-1997 cable insulation and sheathing materials test methods - Part 3. Test method specific to PVC compounds Act 1. temperature pressure test - resistance to cracking (idt IEC 60811-3-1. 1985) GB/T 3956 cable conductor (GB/T 3956-1997, idt IEC 60228. 1978) GB/T 5013.1-2008 rated voltage of 450/750V and below rubber insulated cables - Part 1. General requirements (IEC 60245-1:2003, IDT) GB/T 5013.2-2008 rated voltage of 450/750V and below rubber insulated cables - Part 2. Test methods (IEC 60245-2:1998, IDT) 2 maximum conductor temperature of 110 °C heat-resistant ethylene - vinyl acetate rubber or other equivalent synthetic elastomer insulated, single-core, non-sheathed
750 Vp cable
2.1 Model
Solid or stranded conductors. 60245IEC 04 (YYY);
Flexible conductor. 60245IEC 05 (YRYY).
2.2 Rated voltage
450/750V.
2.3 Structure
2.3.1 Conductor
Number of cores. a core.
Conductor shall comply with GB/T 3956 requirements.
GB/T 5013.7-2008/IEC 60245-7:1994
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 3 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 3956Conductors of insulated cables
- GB/T 3956-1997Conductors of insulated cables
- GB/T 5013.1-2008Rubber insulated cables of rated voltages up to and including 450/750 V -- Part 1: General requirements
- GB/T 5013.2-2008Rubber insulated cables of rated voltages up to and including 450/750 V -- Part 2: Test methods
GB/T 2951.1-1997 · IEC 60811 · GB/T 2951.2-1997 · GB/T 2951.5-1997 · GB/T 2951.6-1997 · IEC 60228 · IEC 60245
Cited by
- GB/T 38428.1-2019Direct current (DC) plugs and socket-outlets for information and communication technology (ICT) equipment installed in data centres and telecom central offices -- Part 1: General requirements
- JB/T 12023-2014250 A~630 A Plugs, Socket-outlets and Couplers for Industrial Purposes
- JB/T 10254-2013Technical requirements for stators and rotors of single-phase series motors for electric tools
How to Download GB/T 5013.7-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 3956-2008 — Conductors of insulated cables
GB/T 39560.1-2020 — Determination of certain substances in electrical and electronic products - Part 1: Introduction and overview
GB/T 39560.10-2024 — Determination of certain substances in electrical and electronic products - Part 10: Polycyclic aromatic hydrocarbons (PAHs) in polymers and electronics by gas chromatography-mass spectrometry (GC-MS)
Secure payment via Stripe
Payments accepted
GB/T 5013.7-2008
$75.00