GB/T 45660-2025Electronics assembly technology - Electronic modules (English PDF)

Foreword

This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1: Structure and drafting rules for standardization documents" Drafting.

This document is modified to adopt IEC 62421:2007 "Electronic assembly technology - Electronic modules".

This document has made the following structural adjustments compared to IEC 62421:2007.

---Terms 3.1 to 3.3 correspond to terms 3.1, 3.3 and 3.5 of IEC 62421:2007.

The technical differences between this document and IEC 62421:2007 and their reasons are as follows.

--- ISO 3 (see 5.3) has been replaced by the normative reference GB/T 321 to adapt to my country's technical conditions and increase operability.

GB/T 2423.28 --- Replaced IEC 60068-2-21 (see 6.3.1) with the normative reference GB/T 2423.60,

IEC 60068-2-20 (see 6.3.2 and 6.3.3) and SJ/T 11200 replaced IEC 60068-2-58 (see 6.3.2 and 6.3.3) to Adapt to my country's technical conditions and increase operability.

--- The normative reference GB/T 2423.5 replaces IEC 60068-2-27 (see 6.3.4), GB/T 2423.10 replaces

IEC 60068-2-6 (see 6.3.5), GB/T 2423.30 replaced IEC 60068-2-45 (see 6.3.6) to adapt to my country's technical standards. Technical conditions and increase operability.

--- The normative reference GB/T 2423.2 replaces IEC 60068-2-2 (see 6.4.1), and GB/T 2423.1 replaces

IEC 60068-2-1 (see 6.4.2), GB/T 2423.3 replaces IEC 60068-2-78 (see 6.4.3), GB/T 2423.22 replaces Changed to IEC 60068-2-14 (see 6.4.4) to adapt to my country's technical conditions and increase operability;

--- Deleted two terms from IEC 62421:2007 (see 3.2 and 3.4 of IEC 62421:2007) because the two terms are in the text Not mentioned. The following editorial changes were made to this document.

--- Add the headers in "Table 1". Low temperature preferred value (°C), High temperature preferred value (°C) to comply with GB/T 1.1-2020 for the table Require.

1 Scope

This document specifies the definitions, business models, interfaces between business partners, the relevant scope of electronic module standardization and a series of common test General requirements for electronic modules such as test methods.

This document applies to the production, manufacture, testing and acceptance of electronic modules.

2 Normative references

The contents of the following documents constitute essential clauses of this document through normative references in this document.

For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to This document.

GB/T 321 Priority numbers and priority number systems (GB/T 321-2005, ISO 3:1973, IDT)

GB/T 2421-2020 Overview and Guidelines for Environmental Testing (IEC 60068-1:2013, IDT)

Note: There is no technical difference between the referenced content of GB/T 2421-2020 and the referenced content of IEC 60068-1:1988.

GB/T 2423.1 Environmental testing for electric and electronic products Part 2: Test methods Test A. Low temperature (GB/T 2423.1-2008,IEC 60068-2-1:2007,IDT)

GB/T 2423.2 Environmental testing for electric and electronic products Part 2: Test methods Test B. High temperature (GB/T 2423.2-2008,IEC 60068-2-2:2007,IDT)

GB/T 2423.3 Environmental testing Part 2: Test method Test Cab. Steady state damp heat test (GB/T 2423.3-2016,IEC 60068-2-78:2012,IDT)

GB/T 2423.5 Environmental testing Part 2: Test method Test Ea and guidance. Impact (GB/T 2423.5-2019, IEC 60068-2-27:2008, IDT)

GB/T 2423.10 Environmental testing Part 2: Test method Test Fc. Vibration (sinusoidal) (GB/T 2423.10-2019, IEC 60068-2-6:2007, IDT)

GB/T 2423.22 Environmental testing Part 2: Test method Test N. Temperature change (GB/T 2423.22-2012, IEC 60068-2-14:2009, IDT)

GB/T 2423.28 Environmental testing for electric and electronic products Part 2: Test methods Test T. Soldering (GB/T 2423.28-2005,IEC 60068-2-20:1979,IDT)

GB/T 2423.30 Environmental testing Part 2: Test methods Test XA and guidance. Immersion in cleaning agents (GB/T 2423.30-2013,IEC 60068-2-45:1980/Amd1.1993,MOD)

GB/T 2423.60 Environmental testing for electric and electronic products Part 2: Test methods Test U. Strength of lead terminals and integral mounting parts Degree (GB/T 2423.60-2008, IEC 60068-2-21:2006, IDT)

SJ/T 11200 Environmental testing Part 2-58.Test Test Td. Solderability of surface mounted components, corrosion resistance of metallization layers and Test method for resistance to soldering heat (SJ/T 11200-2016, IEC 60068-2-58:2004, MOD)