Valid

GB/T 42975-2023Semiconductor integrated circuits—Test method of driver device (English PDF)

半导体集成电路 驱动器测试方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (23 pages)

Need quotation for your management?

Get a formal quotation for GB/T 42975-2023 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

September 7, 2023

Implementation date

January 1, 2024

Scope

GB/T 42975-2023 is the English-translated version of 半导体集成电路 驱动器测试方法.

This document specifies the basic principles and the test procedures for measuring the electrical characteristics of semiconductor integrated circuit drivers.

The document applies to the electrical testing of drivers made by any semiconductor process, including 74/54 series drivers, bus drivers, PIN switch drivers, Darlington drivers, clock drivers, LVDS drivers, MOSFET drivers and differential drivers; drivers of other kinds may be tested following it as a reference.

Found what you need?

Document preview — GB/T 42975-2023

National Standard of the People's Republic of China

ICS
31.200
Classification
L 56

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • PrefaceI
  • 1 Scope
  • 2 Normative reference documents
  • 3 Terms and Definitions
  • 4 General requirements
  • 5 Static parameter test
  • 5.1 Input high level voltage (VIH)
  • 5.2 Input low level voltage (VIL)
  • 5.3 Input clamping voltage (VIK)
  • 5.4 Input high level current (IIH)
  • 5.5 Input low level current (IIL)
  • 5.6 Input impedance (RIN)
  • 5.7 Output high-level voltage (VOH)
  • 5.8 Output low level voltage (VOL)
  • 5.9 Output impedance (ROUT)
  • 5.10 Output leakage current (ILK)
  • 5.11 Output short circuit current (IOS)
  • 5.12 Peak current (IPK)
  • 5.13 Differential output voltage (VOD)
  • 5.14 Differential output voltage change (deltaVOD)
  • 5.15 Common mode output voltage (VOS)
  • 5.16 Common mode output voltage change (deltaVOS)
  • 5.17 Quiescent current (IDDQ)
  • 6 Dynamic Parameter Test
  • 6.1 Supply current (IDD)
  • 6.2 Output transmission delay time from low level to high level (tPLH)
  • 6.3 Output transmission delay time from high level to low level (tPHL)
  • 6.4 Output rise time (tr)
  • 6.5 Output falling time (tf)
  • 6.6 Output Skew (tSK)
  • 6.7 Clock Jitter (jADD)
  • 6.8 Input capacitance (Ci) and output capacitance (CO)

Foreword

This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1: Structure and Drafting Rules of Standardization Documents" Drafting.

1 Scope

This document specifies the basic principles and test procedures of electrical characteristics testing methods for semiconductor integrated circuit drivers (hereinafter referred to as devices).

This document applies to 74/54 series drivers, bus drivers, PIN switch drivers, Darlington drivers, clock drivers, Electrical performance testing of drivers manufactured by various semiconductor processes such as LVDS drivers, MOSFET drivers and differential drivers. other Use as a reference for testing specific drives.

2 Normative reference documents

The contents of the following documents constitute essential provisions of this document through normative references in the text. Among them, the dated quotations For undated referenced documents, only the version corresponding to that date applies to this document; for undated referenced documents, the latest version (including all amendments) applies to this document.

GB/T 9178-1988 Integrated circuit terminology

GB/T 17574-1998 Semiconductor devices integrated circuits Part 2: Digital integrated circuits

3 Terms and definitions

The terms and definitions defined in GB/T 9178-1988 apply to this document.

4 General requirements

4.1 Test environment conditions

Unless otherwise specified, the electrical test ambient temperature is 25 3-5°C; the ambient air pressure is 86kPa~106kPa. If the ambient humidity affects the test Response should be specified in relevant documents.

4.2 Test matters

During the test, the following requirements are met.

a) If there is no special instructions, the range of ambient or reference point temperature deviation from the specified value shall comply with the provisions of the device detailed specifications;

b) External interference should not affect the test accuracy, and the test error caused by the test equipment should comply with the provisions of the device detailed specifications;

c) The power supply voltage applied to the device under test should be within ±1% of the specified value, and the accuracy of other electrical parameters applied to the device under test should comply with Comply with the provisions of device-related documents;

d) When the device under test is connected or disconnected from the test system, the service limit conditions of the device should not be exceeded;

e) Device damage caused by electrostatic discharge should be avoided;

f) Whether the non-tested input terminals and output terminals are left unconnected shall comply with the provisions of relevant documents.

4.3 Related documents

The relevant documents in this document refer to the driver-related product detailed specifications, product manuals and other technical documents.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 23 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 42975-2023

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
23 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 42975-2023

$385.00