Valid

GB/T 39566-2020Micro motors—Axial end play (English PDF)

微电机 轴向间隙

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 39566-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 14, 2020

Implementation date

July 1, 2021

Scope

GB/T 39566-2020 is the English-translated version of 微电机 轴向间隙.

GB/T 39566-2020 is the Chinese standard "Micro motors—Axial end play".

Its scope clause reads: This standard specifies the frame number, structure, value of the axial gap, testing methods and testing rules for the axial gap of the micromotor: This standard is applicable to the design, manufacture, inspection and acceptance of the axial gap of the assembled micromotor with an outer diameter of 16mm ~ 160mm:. Its clauses include terms and definitions; frame number.

Found what you need?

Document preview — GB/T 39566-2020

National Standard of the People's Republic of China

ICS
29.160.30
Classification
K 24

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope1
  • 2 Normative references1
  • 3 Terms and definitions1
  • 4 Frame number1
  • 5 Structure2
  • 6 Axial clearance value2
  • 7 Detection method4
  • 8 Inspection rules5
  • Appendix A (informative appendix) Calculation method of axial clearance6
  • Appendix B (informative appendix) Calculation method of axial clearance tension8

1 Scope

This standard specifies the frame number, structure, value of the axial gap, testing methods and testing rules for the axial gap of the micromotor:

This standard is applicable to the design, manufacture, inspection and acceptance of the axial gap of the assembled micromotor with an outer diameter of 16mm ~ 160mm:

2 Normative references

The following documents are indispensable for the application of this document: For dated reference documents, only the dated version applies to this article

Pieces: For undated references, the latest version (including all amendments) applies to this document:

GB/T 1804-2000 General Tolerance Tolerance of linear and angular dimensions without tolerance

GB/T 2900:26 Electrician terminology control motor

GB/T 7345-2008 Basic technical requirements for control motors

3 Terms and definitions

The following terms and definitions defined in GB/T 2900:26 apply to this document:

3:1

Axial endplay

The two directions apply a prescribed force along the axial direction, which results in a varying distance between the shaft extension end surface and the motor mounting surface:

3:2

Axialmagneticpul

The pulling force generated by the axial magnetic field center between the stator and rotor of the motor does not coincide:

3:3

Temperaturerise

The micromotor generates current heating effect, iron loss and mechanical loss after the winding is energized: As time goes by, when the heat and heat dissipation are balanced, it is higher than

The value of the ambient temperature:

3:4

Bearingspan

The distance between the inner end faces of the bearings at the front and rear ends of the micromotor rotor:

4 Frame number

The frame number is expressed by diameter: When the micro-motor has a non-cylindrical structure, it is expressed by the diameter of the inscribed circle of the non-cylindrical section:

The corresponding relationship between the frame number and the outer diameter should comply with Table 1 or the product-specific technical conditions: The outer diameter is greater than 160mm by the product-specific technology

The technical conditions are stipulated:

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 39566-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 39566-2020

$175.00